Genuine Cadillac Fleetwood Sway Bar Kit

Cadillac Fleetwood Sway Bar Kit Parts Questions & Answers

• Shaft Assembly, Front Stabilizer
  14081407
  Q: How do you remove and install the front stabilizer bar on Cadillac ElDorado and Fleetwood?

  A: To remove and install a stabilizer bar on a Deville or Fleetwood, you should start by raising and supporting the vehicle. Take off the wheel and tire assemblies, stabilizer bar link bolts from lower Control Arms and stabilizer bar bushing brackets from frame. Using a separator tool, disconnect tie rod ends from Steering Knuckles, disconnect exhaust pipe from exhaust manifold. Twist passenger side strut all the way to right, then slide the stabilizer bar over the steering knuckle and pull it down until it clears the frame. To install, slide stabilizer bar back into position while loosely installing mount bushings, brackets, bolts. Loosely attach link components of stabilizer bar to lower control arms, connect tie rod ends to steering knuckles and tighten nuts. Stabilizer bar bracket bolts are tightened as well as stabilizer bar link bolt nuts. Finally, reconnect exhaust pipe with manifold, install wheel and tire assemblies then lower vehicle. In this process for Eldorado and Seville models though, there are additional steps: removing road sensing suspension position sensor from lower control arm; disconnecting muffler pipe from manifold. The next step is positioning and installing the Sway Bar Kit followed by connecting exhaust pipe again and installation of bushings brackets and stabilization links. Then people fasten bracket bolts as well as stabilization link nuts; if applicable they will reinstall road sensing suspension position sensor. Finally we go to installation of right side wheel and tire assembly lowered vehicle.
• Shaft, Rear Stabilizer
  25558115
  Q: How to remove and install the rear stabilizer bar on Cadillac ElDorado and Fleetwood?

  A: To get rid of and set up a Sway Bar Kit on various Cadillac models, follow these steps: For the Deville and Fleetwood, start by raising and safely supporting the car, remove the back wheel and tire assemblies. And then take away from the stabilizing connection bolt link nut retainer together with bushings from your stabilizer pub group. Take away the weblink bolt and fold the available stop in the hyperlink downwards, allowing you to remove the stabilizer nightclub along with bushes. To put in, place the Bushing into your link that has a slit going through in reverse in the vehicle; fold up hyperlink over bushing and place website link bolt. Lastly install link bushings, retainersupport screw, nut tightening attach by 13 ft lbs (17 Nm) and attach at 37 ft lbs (50 Nm) for 1990-91 vehicles or 17 ft lbs (23 Nm) for 1992-98 vehicles. For Eldorado as well as Seville designs of 1990-92 it is suggested to carryout removal and installation of stablilizer using bottom wheels while vehicle on ground If necessary employ drive-on ramps or support Control Arms having jacks as possible outboard Start off by raising and safely supporting the car, release Sway Bar attaching nut along with bolt at strut also stabilizer link bolt together with nut at suspension support. Eliminate Sway Bar Kit from vehicle; remove also if desired stability links including bushes. To install inspect bushings for damage, replace if neccessary then put on bushings nd links to Sway Bar Place Sway Bar within vechile fix bolts nd nuts t suspension supports nd strut; tighten linkage bolt nd stabeliser mounting nuts to 43ft lbs.(58Nm). For Eldorado plus Seville types over years between 1993-98 lift up car securely remove rear wheel as well as tire assemblies at that point take away from stabilizer link lower bolt for both sides of vehicle. Remove brackets and bushings from Sway Bar Kit. Lower and hold up exhaust program at the back of vehicle then remove Sway Bar Position Sway Bar inside car lift up propperly exhaust system nd secure it Put bushings on Sway Bar and attach brackets; fit upper link nuts nd lower bolts tighten upper link to 38 ft lbs (52 Nm) and lower link to 44 ft lbs (60 Nm). Lastly tighten stabalizer bracket bolt at 44 ft lbs (60 Nm), install wheel/tire assembly, drop vehicle.