Make sure this part fits

Pontiac 7846169 Front Wheel Drive Shaft

1985-1989 Pontiac

Customer Questions & Expert Answers (5)
GM 7846169 Front Wheel Drive Shaft
  • Part Description
    Shaft,Front Wheel Drive
  • Position
    Front
  • Manufacturer
    General Motors
Make sure this part fits
$50.43 MSRP: $90.46
You Save: $40.03 (45%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number7846169
    Part DescriptionShaft,Front Wheel Drive
    Other NamesAxle Shaft, Shaft
    Item Weight4.00 Pounds
    PositionFront
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU7846169
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1985-1989 Pontiac 60004 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 4.3L Diesel2 DOOR, 4 DOOR, LE 2 DOOR, LE 4 DOOR, LE STATION WAGON, SE 4 DOOR, SE STATION WAGON, STATION WAGON, STE 4 DOOR
    1987-1989 Pontiac Bonneville6 Cyl 3.8L4 DOOR, LE 4 DOOR, SE 4 DOOR, SSE 4 DOOR
    1988-1989 Pontiac Grand Prix6 Cyl 2.8L, 6 Cyl 3.1L2 DOOR, LE 2 DOOR, SE 2 DOOR
  • Customer Questions & Expert Answers

    Q:
    Will this part number fit my car? Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 7846169 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How do you remove and install a half shaft? Posted by Customer
    A:
    To start removing and installing an axle shaft, begin by raising the vehicle and supporting it. Remove the wheel and tire assembly and install a modified boot protector on the outer CV-joint. Thereafter, insert a drift punch into the caliper and rotor to prevent the rotor from turning before undoing the hub nut. Proceed to disconnect the stabilizer link if necessary. The ball joint cotter pin should be removed first then its nut followed by loosening it in relation with knuckle by using an appropriate tool. The ball joint must be separated from this steering knuckle using a prybar afterwards. After, partially install the hub nut for thread protection and remove the axle shaft from the hub with a suitable tool. Move strut and knuckle rearward. Separate the axle shaft from the transaxle using a prybar with a wood block fulcrum to protect the transaxle case. For installation purposes, where applicable you can start by putting on the right side axle shaft. In order to seat, tap until seated into the transaxle is done when installing the axle shaft then the snap ring should be checked whether or not it is seated. Installation of the axle shaft into the hub bearing assembly is next and a new hub nut can be loosely installed. Connect the ball joint in the steering knuckle by tightening its nut. Torque specified ball joint nuts while inserting new cotter pins. Insert a drift punch between the caliper as well as the rotor so that the rotor will be prevented from turning hence tighten the hub nut within specified torque limits. Reinstall (if removed) stabilizer link but now without the boot protector. Remove any installation tools when applicable. Finally, fit back the wheel again plus tire among other things before lowering the vehicle down after completion of all repairs.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done after raising the 1997 Oldsmobile Cutlass? Posted by Customer
    A:
    After raising the vehicle, the wheel and brake drum should be removed.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What should you do before installing the new bearing of the 1988 Oldsmobile Cutlass? Posted by Customer
    A:
    Before installing the new bearing, make sure to install the retainer plate and the seal to the shaft first.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How much weight should be taken up by the floor jack of the 1995 Oldsmobile Cutlass? Posted by Customer
    A:
    Just take up the weight, but do not raise sufficiently to take the weight of the vehicle from the frame stands.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 7846169, the Right Choice

Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 7846169 Front Wheel Drive Shaft. It is sometimes referred to as Pontiac Axle Shaft. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific Pontiac 6000, Bonneville, Grand Prix models.

Affordable, reliable and built to last, GM part # 7846169 Front Wheel Drive Shaft stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly