Make sure this part fits

Pontiac 7846269 SHAFT

1983-1989 Pontiac 6000

Customer Questions & Expert Answers (9)
GM 7846269 SHAFT
  • Part Description
    Shaft
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number7846269
    Part DescriptionShaft
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU7846269
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1983-1989 Pontiac 60004 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 4.3L Diesel2 DOOR, 4 DOOR, LE 2 DOOR, LE 4 DOOR, LE STATION WAGON, SE 4 DOOR, SE STATION WAGON, STATION WAGON, STE 2 DOOR, STE 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    Will this part number fit my car? Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 7846269 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install the Axle Shaft for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To remove the hub nut, lift the front of the car and prop it up with jackstands. After that, take off the wheel and disconnect a brake line clip from a strut. Then without breaking apart an inlet line, get away with disc brake caliper. On installation mark must be made on cam bolt to equal this adjustment for camber. Remove both the Cam bolt and upper attaching bolt; then remove steering knuckle assembly from strut bracket. Use GM special tool or equivalent to draw axle shaft out of transaxle and remove axle shaft from hub and bearing assembly using same tool. In case axle shaft requires overhaul, automotive mechanic shop should press seal retainers in place. Also replace steering knuckle seal when replacing axle shaft. Install axle shaft loosely into steering knuckle and transaxle; also loosely attach steering knuckle onto strut bracket. Mount brake caliper followed by axle shaft into steering knuckle secured with hub nut tightly. Lower car just enough to align cam bolt with alignment marks; torque both cam bolt & upper nut down to specs. Connect the axle shaft to transaxle by tapping until seated appropriately. Attach brake line clip onto strut bracket, mount wheel, lower car to ground. Lastly, torque hub nut down to specs.
    Posted by GMPartsGiant Specialist
    Q:
    How do you remove the rear axle for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To remove the rear axle, start by removing the rear springs and disconnecting the brake lines from the control arm attachment. Disconnect and cap rigid brake lines from both rear brake cylinders and disconnect the right rear parking brake cable from the left rear parking brake cable. Next, disconnect the right rear and left rear parking brake cables from their brackets on the rear axle. Remove bolts securing the rear parking brake cable guide to underbody and allow whole parking brake assembly to hang loose from right rear backing plate. Remove bolts securing hub and bearing assembly to rear axle; remove assemblies with brake backing plates. With another person's help, steady jack under the rear axle and remove bolts that secure control arm brackets to body. Lower, pull out of underneath car. In case of replacing a new axle again, remove control arm brackets from control arms and install them on new axle. Inspect control arm bushings for any damage necessary. Before installing make sure that lower edge of control arms is true horizontal plain and adjust control arm brackets to 45° angle if required. Reverse order of removal in installing rear axel ensuring not to tighten lower shock nuts or track arm nuts until car is lowered onto suspension with its full weight on it. Finally, bleed the brakes system as usual then adjust parking Brake.
    Posted by GMPartsGiant Specialist
    Q:
    What should be used to seal the axle housing cover when draining and refilling the rear axle lubricant for the 1986 Buick Century? Posted by Customer
    A:
    A suitable gasket should be used to seal the axle housing cover.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What type of drive axles are used in the X-Body cars for the 1985 Buick Skylark? Posted by Customer
    A:
    The X-Body cars utilize double offset drive axles.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How do you remove the seal retainer from the outer joint assembly for the 1981 Buick Skylark? Posted by Customer
    A:
    To remove the seal retainer from the outer joint assembly, gently tap it evenly around the retainer.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What should be done after removing the wheel and brake drum of the 1993 Oldsmobile Cutlass? Posted by Customer
    A:
    After removing the wheel and brake drum, the pressed steel cover from the differential carrier should be unscrewed and removed, allowing the oil to drain into a suitable container.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What should you do before installing the new bearing of the 1995 Oldsmobile Cutlass? Posted by Customer
    A:
    Before installing the new bearing, make sure to install the retainer plate and the seal to the shaft first.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How should the 1992 Oldsmobile Cutlass be raised and supported? Posted by Customer
    A:
    Raise the rear of the vehicle and support it securely on stands placed under the body frame rails.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 7846269, the Right Choice

Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 7846269 SHAFT. It is sometimes referred to as Pontiac Axle Shaft. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific Pontiac 6000 models.

Affordable, reliable and built to last, GM part # 7846269 SHAFT stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly