How do you remove the ignition switch?

Proceed with removing the ignition switch by disconnecting the two wiring leads, starting with the one farthest from the steering wheel. Remove the stud and screw securing the switch to the column, and lift off the switch, making sure to pull it up from the column due to the protruding ignition actuator rod. Before installing the new switch, use a flat-head screwdriver to move the slider inside the switch to the 'Accessory' position on the extreme right, then slide it two detents to the left to the 'off/unlock' position. This position is necessary for installation. Place the switch on the column, guiding the actuator rod into the slider recess. Install the stud and screw, tightening them to specifications. Finally, connect the two wiring leads to the switch and reverse the procedure.

Genuine Oldsmobile Omega Ignition Switch

Starter Ignition Switch

Enter your vehicle info to find more parts and verify fitment

Select Vehicle by VIN
Select Vehicle by Model

Select by VIN

Enter your VIN for the most accurate results.

Select by Model

-- Select Make --

-- Select Model --

-- Select Year --

5 Ignition Switches found

View related parts
Oldsmobile Omega Switch,Ignition & Start
Part Number: 1990116
- Other Name: SWITCH, Ignition Switch; Ignition Switch
More Info
Fits the following Vehicles:
1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
Less Info
View related parts
Oldsmobile Omega Switch,Steering Column Ignition
Part Number: 1990115
- Other Name: SWITCH, Ignition Switch; Ignition Switch
More Info
Fits the following Vehicles:
1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
Less Info
View related parts
Oldsmobile Omega Switch,Steering Column Ignition Lock
Part Number: 7843451
- Other Name: SWITCH, Ignition Switch; Ignition Lock Cylinder, Ignition Switch
More Info
Fits the following Vehicles:
1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
Less Info
View related parts
Oldsmobile Omega Switch,Ignition Key Alarm
Part Number: 26022717
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
More Info
Fits the following Vehicles:
1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
Less Info
View related parts
Oldsmobile Omega Switch Assembly, Ignition Key Warning Alarm
Part Number: 7804414
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
More Info
Fits the following Vehicles:
1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
Less Info

Oldsmobile Omega Ignition Switch Parts Questions & Answers

Switch,Steering Column Ignition
1990115
Q: How do you remove the ignition switch?
A: Proceed with removing the ignition switch by disconnecting the two wiring leads, starting with the one farthest from the steering wheel. Remove the stud and screw securing the switch to the column, and lift off the switch, making sure to pull it up from the column due to the protruding ignition actuator rod. Before installing the new switch, use a flat-head screwdriver to move the slider inside the switch to the 'Accessory' position on the extreme right, then slide it two detents to the left to the 'off/unlock' position. This position is necessary for installation. Place the switch on the column, guiding the actuator rod into the slider recess. Install the stud and screw, tightening them to specifications. Finally, connect the two wiring leads to the switch and reverse the procedure.