Genuine Chevrolet Silverado Wheel Bearing

Chevrolet Silverado Wheel Bearing Parts Questions & Answers

• Rear Wheel Bearing
  23455948
  Q: How to remove and install a rear hub assembly,Wheel Bearing and Wheel Seal for Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

  A: To remove and install a rear hub assembly, first remove the axleshaft and rear wheels, then remove the brake disc and retaining ring/key from the end of the axle housing. Use a special socket to remove the adjusting nut and pull the hub assembly straight off the axle tube. Discard the oil seal and clean and inspect all components for wear or damage. Disassemble the hub further if necessary, then clean and reassemble using new bearing cups and lubricating with wheel bearing grease. To install, place the hub assembly on the axle tube and adjust the bearings by tightening the adjusting nut to 50 ft-lbs, then backing it off and tightening it hand-tight. Install the key and retaining ring, and ensure there is no play in the hub assembly before reinstalling the axleshaft and lowering the vehicle.
• Rear Wheel Bearing
  25855296
  Q: How to replace a rear bearing in an axle housing on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

  A: To remove and replace a bearing in an axle housing, first remove the axleshaft and oil seal. Use a bearing puller and slide hammer to extract the old bearing from the housing. Clean out the recess and install the new bearing using a bearing installer or a piece of pipe against the outer race. Ensure the bearing is tapped in fully. Finally, install a new oil seal and re-install the axleshaft.
• Rear Wheel Bearing
  25843093
  Q: How do you remove and install right Axle Shaft,Shift Fork and Wheel Bearing on 4WD and AWD Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

  A: To remove and install components in the front Differential of selectable 4WD systems, first, loosen the wheel lug nuts and raise the vehicle securely on jackstands. Remove the right front wheel and the differential carrier splash shield if equipped. Drain the lubricant from the front differential. For 4WD systems, unbolt the right driveaxle from the axleshaft flange and support it out of the way. Remove the front axle shift motor and, if applicable, disconnect the front stabilizer link or remove the front shock absorber/coil spring assembly. On 2500/3500 models, remove the front axle bracket bolts and slide the bracket forward for additional clearance. Support the differential carrier with a floor jack and block of wood. Remove the bolts securing the axle tube to the differential carrier and the nuts attaching the tube to its support bracket. Carefully remove the output shaft tube, ensuring no components fall out. Mount the tube in a vise and remove the internal components. Measure and remove the axleshaft bearing using a slide hammer and bearing remover attachment. For installation, install the bearing to the original depth using a bearing driver or socket, then install a new seal and deflector, lubricating the seal lips with grease. Carefully drive in the axleshaft, followed by the internal components. Apply RTV sealant to the tube-to-differential housing mating surface, and install the tube assembly, tightening bolts and nuts to specified torques. Reinstall the driveaxle, front axle shift motor, and fill the differential with lubricant. For AWD systems, remove the stabilizer bar link and, if applicable, the front shock absorber. Unbolt the right driveaxle from the axleshaft flange, supporting it properly. Support the differential carrier with a floor jack and a block of wood. Remove nuts attaching the axle shaft to its support bracket and the bolts securing the axle shaft flange to the differential carrier. Use a brass punch and hammer to separate the axle shaft from the differential case side gear. Remove the inner axle shaft assembly and axle shaft. Replace the inner seal and bearing with a special tool, then apply RTV sealant to the differential sealing surface and install the inner axle shaft housing assembly. Install the axle shaft to the support bracket and align the splines with the differential side gear. Tap the axle shaft with a mallet until the ring (clip) aligns with the groove in the differential case side gear. Install the axle shaft to the inner flange and tighten the bolts. Reinstall the stabilizer link, fill the differential with lubricant, install the differential carrier splash shield, and finally, install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts, and check for proper operation.
• Wheel Bearing
  15042155
  Q: How to replace and install the front Wheel Bearing and Wheel Seal of 4WD Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

  A: To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left Axle Shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.