My Garage
My Account
Cart
Genuine 1994 Chevrolet Beretta Intake Manifold
Engine Intake Manifold- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 Intake Manifolds found
Product Specifications- Other Name: MANIFOLD, Fuel Injection Air Meter; Intake Manifold, Throttle Body
- Position: Upper
- Item Weight: 5.40 Pounds
- Item Dimensions: 18.3 x 11.0 x 9.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17112896
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: MANIFOLD, Engine Fuel Intake Manifold; Intake Manifold, Manifold
- Position: Lower
- Item Weight: 13.10 Pounds
- Item Dimensions: 21.2 x 14.9 x 10.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 24505662
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: MANIFOLD, Engine Fuel Intake Manifold; Intake Manifold
- Position: Upper
- Item Weight: 7.90 Pounds
- Item Dimensions: 21.9 x 11.7 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10137068
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: MANIFOLD, Engine Fuel Intake Manifold; Intake Manifold
- Item Weight: 12.50 Pounds
- Item Dimensions: 23.6 x 11.0 x 9.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 24572301
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: MANIFOLD, Engine Fuel Intake Manifold; Intake Manifold, Manifold
- Position: Lower
- Item Weight: 13.60 Pounds
- Item Dimensions: 21.5 x 17.6 x 9.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17087537
- Warranty: This genuine part is guaranteed by GM's factory warranty.
- Product Specifications
- Other Name: MANIFOLD, Engine Fuel Intake Manifold; Throttle Body
- Position: Upper
- Item Weight: 5.60 Pounds
- Item Dimensions: 18.0 x 11.1 x 9.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17112902
- Warranty: This genuine part is guaranteed by GM's factory warranty.
1994 Chevrolet Beretta Intake Manifold
We are your prime source for competitively priced and high-quality OEM 1994 Chevrolet Beretta Intake Manifold. We provide you with parts that will allow you to save a lot of money without sacrificing quality. All our OEM parts are backed by the manufacturer's warranty and shipped out at a swift rate.
1994 Chevrolet Beretta Parts Questions & Experts Answers
- Q: How to remove the intake manifold in 2.3L four cylinder (Quad-4) engine on 1994 Chevrolet Beretta?A: To take out the intake manifold, it is necessary to first reduce the fuel system pressure and remove the negative battery cable. Next, empty the cooling system then carry out removal of throttle body. Start by labeling vacuum and breather hoses, electrical wires etc before removing oil/air separator, oil fill cap and dipstick assembly. Unbolt / detach oil fill tube from engine block; remove intake manifold brace then loosen up manifold mounting nuts/bolts. In case of need use soft-face hammer to displace manifold away from cylinder head. For proper installation ensure that mating surfaces of cylinder head and manifold are clean and make use of gasket scraper to get rid of old sealant as well as gasket material. Clean mating surfaces with lacquer thinner or acetone. Chase threads in bolt holes with tap; blow out chips with compressed air; put gasket on cylinder head with all openings properly aligned; place intake manifold without tearing gasket; start nuts /bolts by hand then three step tighten them down finally reverse remaining removal steps, start engine up and check for leaks at intake manifold joints.
