How to remove and reinstall the turn signal switch assembly on Chevrolet Beretta?

On the models that have the Delco Loe II or Theft lock audio system, first, make sure that the lockout is disabled before disconnecting the battery. Start with the removal of the cable of cable connected to the negative battery terminal. That must be followed by the removal of the steering wheel as well as the cancel cam assembly. Remove the hazard warning knob by unscrewing the knob and the screw that is fitted on it. The turn signal lever mounting screw has to be undone and so does the housing cover screw, then take off the turn signal arm and then housing away from the column together with the lever and the housing. It remain, however necessary to remove the plastic spacer in the lower left corner of the housing as it would be needed for the next step. Go ahead to take off the under-dash panel that is situated just below the steering column. It is also necessary to remove screws in the steering column bracket and to release the steering column from the top of the dash. Find that the harness for the turn signal switch is held on by two wiring tabs and remove the wires that connect to the buzzer switch assembly; the black and tan wire, and the light green wire. Pull the electrical lead and connector upwards and disconnect it, and then undo the mounting screws of the turn signal switch assembly and therefore, snap it off. Installation is performed in the exact opposite order to that of removal.

Genuine Chevrolet Beretta Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Turn Signal Switches found

View related parts
Chevrolet Beretta Lever Assembly, Turn Signal Switch
Part Number: 25075810
$15.39 MSRP: $38.10
You Save: $22.71 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: LEVER, Turn Signal Control; Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Lever Assembly, Turn Signal & Steering Column
Part Number: 10131644
$15.53 MSRP: $31.31
You Save: $15.78 (51%)
ADD TO CART
Product Specifications
- Other Name: LEVER, Turn Signal Control; Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Switch, Turn Signal
Part Number: 1997069
$53.31 MSRP: $172.02
You Save: $118.71 (70%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Turn Signal Lamp; Turn Signal Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 2.8L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Switch,Dimmer Pivot
Part Number: 26000862
$40.81 MSRP: $82.30
You Save: $41.49 (51%)
ADD TO CART
Product Specifications
- Other Name: LEVER, Turn Signal Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Turn Signal Switch
Part Number: 19005030
Product Specifications
- Other Name: SWITCH, Turn Signal Lamp; Signal Switch, Turn Signal Switch
- Replaces: 01995901, 19005012, 1995901
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Turn Signal Switch Assembly
Part Number: 1995963
Product Specifications
- Other Name: SWITCH, Turn Signal Lamp
- Replaces: 1995906
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Turn Signal Switch Assembly
Part Number: 1995974
Product Specifications
- Other Name: SWITCH, Turn Signal Lamp; Signal Switch, Turn Signal Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Lever Asm,Turn Signal Switch
Part Number: 12508570
Product Specifications
- Other Name: LEVER, Turn Signal Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Switch, Turn Signal
Part Number: 1997070
Product Specifications
- Other Name: SWITCH, Turn Signal Lamp; Signal Switch, Turn Signal Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 2.8L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Lever, Cruise
Part Number: 25111818
Product Specifications
- Other Name: LEVER, Turn Signal Control; Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 3.1L

Chevrolet Beretta Turn Signal Switch

The main purpose behind the Chevrolet Beretta Turn Signal Switch is to allow the driver to clearly communicate a lane change or turn to those around the vehicle. The Turn Signal Switch is mounted as a lever on the steering column. When the driver flicks the lever, it sends an electrical pulse to either the left or right indicator lamps. There are toggles for headlights and fog lamps. Similarly, you can also toggle wiper speed and cruise control. Thus, it allows excess lighting and convenience tasks in a single reach. Due to the multiple functions of the Turn Signal Switch, internal contacts and internal return springs are quite robust so that they can ensure completion and reopening of the circuit with a click sound. Earlier Beretta editions applied to employ an old-style Turn Signal Switch equipped only for signaling. Later switch units applied on the same Chevrolet platform also combined the added lighting and wiper controls to reduce stalks. Every type of Chevrolet Beretta needs to signal the right thing to other motorists as proper functionality is essential to keep the lights flashing in sync on the Chevrolet Beretta. In light of this, the right fit to match the vehicle year, wiring layout, and connector shape is essential to restoring the full functionality of the switch. Regardless of style, a defective or broken Turn Signal Switch can leave blinkers dark.

Each OEM Chevrolet Beretta Turn Signal Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Beretta Turn Signal Switch Parts Questions & Experts Answers

Lever Assembly, Turn Signal Switch
25075810
Q: How to remove and reinstall the turn signal switch assembly on Chevrolet Beretta?
A:
On the models that have the Delco Loe II or Theft lock audio system, first, make sure that the lockout is disabled before disconnecting the battery. Start with the removal of the cable of cable connected to the negative battery terminal. That must be followed by the removal of the steering wheel as well as the cancel cam assembly. Remove the hazard warning knob by unscrewing the knob and the screw that is fitted on it. The turn signal lever mounting screw has to be undone and so does the housing cover screw, then take off the turn signal arm and then housing away from the column together with the lever and the housing. It remain, however necessary to remove the plastic spacer in the lower left corner of the housing as it would be needed for the next step. Go ahead to take off the under-dash panel that is situated just below the steering column. It is also necessary to remove screws in the steering column bracket and to release the steering column from the top of the dash. Find that the harness for the turn signal switch is held on by two wiring tabs and remove the wires that connect to the buzzer switch assembly; the black and tan wire, and the light green wire. Pull the electrical lead and connector upwards and disconnect it, and then undo the mounting screws of the turn signal switch assembly and therefore, snap it off. Installation is performed in the exact opposite order to that of removal.

Related Chevrolet Beretta Parts

Browse by Year

1996 Turn Signal Switch 1995 Turn Signal Switch 1994 Turn Signal Switch 1993 Turn Signal Switch 1992 Turn Signal Switch 1991 Turn Signal Switch 1990 Turn Signal Switch 1989 Turn Signal Switch 1988 Turn Signal Switch 1987 Turn Signal Switch