How to disconnect and replace the Ignition Lock Cylinder and Ignition Switch on Chevrolet Camaro?

Disconnect the cable from the negative terminal of the battery. Remove the knee bolster trim panel, the knee bolster, and the upper and lower steering column covers, then lower the steering column to its lowest position. Remove the locking pin and disconnect the electrical connector from the ignition switch by depressing the red locking pin. Take out the ignition switch mounting fasteners and the ignition switch from the steering column, ensuring that the new switch snaps into place during installation, which follows the reverse of removal. Turn the ignition key to the RUN position and use a suitable tool to depress the Ignition Lock Cylinder release button located at the top, then remove the Ignition Lock Cylinder. For installation, insert the Ignition Lock Cylinder into the housing and push it in until it clicks. If replacing, ensure it is properly coded to match the original by a dealer service department. Verify that the ignition switch operates correctly in the OFF, ACC, RUN, and START positions, with installation following the reverse of removal. Removal of the lock cylinder illumination ring is not necessary for lock cylinder replacement; however, disconnect the electrical connector from the illumination ring, disengage the lock tabs, and remove the illumination ring, ensuring that it snaps into place during installation.

Genuine Chevrolet Camaro Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Ignition Switches found

View related parts
Chevrolet Camaro Switch Assembly, On/Off Vehicle *Galvano Silvv
Part Number: 23402526
$44.14 MSRP: $90.30
You Save: $46.16 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch, Power Switch, Start Button
- Replaces: 22774052, 23228792
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | 2 DOOR CONVERTIBLE 1LS/1LT, 2 DOOR CONVERTIBLE 1LT, 2 DOOR CONVERTIBLE 1SS, 2 DOOR CONVERTIBLE 2LT, 2 DOOR CONVERTIBLE 2SS, 2 DOOR CONVERTIBLE HI PERFORMANCE, 2 DOOR CONVERTIBLE HIGH PERFORMANCE, 2 DOOR COUPE 1LS/1LT, 2 DOOR COUPE 1LT, 2 DOOR COUPE 1SS, 2 DOOR COUPE 2LT, 2 DOOR COUPE 2SS, 2 DOOR COUPE HI PERFORMANCE, 2 DOOR COUPE HIGH PERFORMANCE | 4 Cyl 2.0L, 6 Cyl 3.6L, 8 Cyl 6.2L
View related parts
Chevrolet Camaro Switch,Ignition & Start
Part Number: 20965947
$18.53 MSRP: $34.96
You Save: $16.43 (47%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Replaces: 92184907
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | 2 DOOR CONVERTIBLE, 2 DOOR COUPE, LS 2 DOOR COUPE, LT 2 DOOR CONVERTIBLE, LT 2 DOOR COUPE, SS 2 DOOR CONVERTIBLE, SS 2 DOOR COUPE | 6 Cyl 3.6L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Camaro Switch,Steering Column Ignition Lock
Part Number: 7843451
$33.92 MSRP: $63.56
You Save: $29.64 (47%)
ADD TO CART
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Lock Cylinder, Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1992 Chevrolet Camaro | RS 2 DOOR, RS CONVERTIBLE | 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Switch,Ignition & Start
Part Number: 1990116
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE, RS 2 DOOR, RS CONVERTIBLE | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.0L, 8 Cyl 5.7L
- 1982-1989 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Switch,Steering Column Ignition
Part Number: 1990115
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1989 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Switch,Ignition
Part Number: 26036235
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE | 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Switch,Ignition Key Alarm
Part Number: 26022717
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2002 Chevrolet Camaro | 2 DOOR, 4 DOOR, CONVERTIBLE, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Switch Assembly, Ignition Key Warning Alarm
Part Number: 7804414
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1989 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 8 Cyl 5.0L, 8 Cyl 5.7L

Chevrolet Camaro Ignition Switch

In the Chevrolet Camaro vehicular system, the Ignition Switch plays a central role in the ignition and charging circuits whereby it helps to start the engine apart from operating electrical devices including but not limited to radio and power windows. Previously, Chevrolet Camaro cars incorporated a mechanical key for operating the Ignition Switch where the Switch could only be unlock by the specific key. Over the years, there have been development which has seen some Chevrolet Camaro comes with what is normally referred to as the key-less ignition system that uses a push button but still needs a transponder signal to start. This change indicates the movement towards the contemporary comfort while the purpose of the Ignition Switch stays the same. In any case, the Ignition Switch in Chevrolet Camaro cars is easy to change as it is wired according to the type of car model in a way that is usually plug and play.

Each OEM Chevrolet Camaro Ignition Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Camaro Ignition Switch Parts Questions & Experts Answers

Switch,Ignition & Start
20965947
Q: How to disconnect and replace the Ignition Lock Cylinder and Ignition Switch on Chevrolet Camaro?
A:
Disconnect the cable from the negative terminal of the battery. Remove the knee bolster trim panel, the knee bolster, and the upper and lower steering column covers, then lower the steering column to its lowest position. Remove the locking pin and disconnect the electrical connector from the ignition switch by depressing the red locking pin. Take out the ignition switch mounting fasteners and the ignition switch from the steering column, ensuring that the new switch snaps into place during installation, which follows the reverse of removal. Turn the ignition key to the RUN position and use a suitable tool to depress the Ignition Lock Cylinder release button located at the top, then remove the Ignition Lock Cylinder. For installation, insert the Ignition Lock Cylinder into the housing and push it in until it clicks. If replacing, ensure it is properly coded to match the original by a dealer service department. Verify that the ignition switch operates correctly in the OFF, ACC, RUN, and START positions, with installation following the reverse of removal. Removal of the lock cylinder illumination ring is not necessary for lock cylinder replacement; however, disconnect the electrical connector from the illumination ring, disengage the lock tabs, and remove the illumination ring, ensuring that it snaps into place during installation.