How to replace the transfer case seal on Chevrolet Equinox?

This procedure applies only to NVG-900 transfer cases, as the output shaft seal on the Getrag 760 transfer case is not typically serviced while in the vehicle. Begin by raising the vehicle and securely supporting it on jackstands. Drain the transfer case lubricant, then remove the driveshaft. Mark the relative positions of the pinion, nut, and flange. Use a beam-or dial-type inch-pound torque wrench to determine the torque required to rotate the pinion and record it for later use. Count the number of threads visible between the end of the nut and the end of the pinion shaft, and record that as well. Remove the flange mounting nut using a chain wrench to hold the pinion flange while loosening the locknut. A small puller will be required to remove the companion flange, ensuring it has two bolts that screw into the companion flange. Pry out the seal with a screwdriver or seal removal tool, taking care not to damage the seal bore. Lubricate the lips of the new seal with multi-purpose grease and tap it evenly into position with a seal installation tool or a large socket, ensuring it enters the housing squarely and is tapped to its full depth. Align the mating marks made before disassembly and install the companion flange, tightening the pinion nut if necessary to draw the flange into place. Carefully tighten the nut until the original number of threads are exposed and the marks are aligned. Measure the torque required to rotate the pinion and tighten the nut in small increments until it matches the previously recorded figure. Finally, connect the driveshaft, add the specified lubricant to the transfer case, and lower the vehicle.

Genuine Chevrolet Equinox Transfer Case Seal

Transfer Case Output Shaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Transfer Case Seals found

View related parts
Chevrolet Equinox Seal, Power Transfer U Face
Part Number: 23277803
$2.09 MSRP: $3.46
You Save: $1.37 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case; Input Shaft Seal
- Replaces: 19208891
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Input Shaft
Part Number: 19210795
$33.73 MSRP: $55.83
You Save: $22.10 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Replaces: 19132942
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Input Shaft (Right)
Part Number: 19132945
$34.10 MSRP: $56.44
You Save: $22.34 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Rear Output Shaft
Part Number: 19132939
$19.48 MSRP: $32.24
You Save: $12.76 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Input Shaft
Part Number: 12569986
$22.21 MSRP: $36.75
You Save: $14.54 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Equinox | SUV AWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal, Differential Drive Pinion Gear (O Ring)
Part Number: 23206807
$0.71 MSRP: $1.34
You Save: $0.63 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal,Transfer Case Rear Output Shaft
Part Number: 12569965
$30.70 MSRP: $48.29
You Save: $17.59 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Equinox | SUV AWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Input Shaft (O Ring)
Part Number: 19132943
$4.21 MSRP: $6.97
You Save: $2.76 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Transfer Case Intermediate Drive Shaft Seal (O, Ring)
Part Number: 19132944
$0.35 MSRP: $0.58
You Save: $0.23 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal,Transfer Case Intermediate Drive Shaft (O, Ring); Input Shaft Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ , LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L, 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Intermediate Drive Shaft (Radial Lip)
Part Number: 19206322
$38.98 MSRP: $61.33
You Save: $22.35 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case
Part Number: 19132946
$12.27 MSRP: $19.58
You Save: $7.31 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Transfer Case Rear Output Drive Shaft Housing (O Ring)
Part Number: 19208892
$23.11 MSRP: $36.84
You Save: $13.73 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Position: Rear
- Replaces: 19132940
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal, Pwr Trfer U Output Shf
Part Number: 84681932
$31.69 MSRP: $52.46
You Save: $20.77 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Output Shaft Seal
- Replaced by: 85732461
- Replaces: 23432724, 84585185
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal, Power Transfer U Face
Part Number: 84297549
$2.80 MSRP: $4.63
You Save: $1.83 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Pwr Trfer U Face; Input Shaft Seal
- Replaces: 23432719
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal, Power Transfer U Cover To Intermediate Drive Shaft
Part Number: 23432721
$30.98 MSRP: $49.40
You Save: $18.42 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case; Output Shaft Seal
- Replaced by: 85732462
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal,Transfer Case
Part Number: 19178699
$46.95 MSRP: $74.88
You Save: $27.93 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transfer Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV | 4 Cyl 2.4L, 6 Cyl 3.6L
- 2009 Chevrolet Equinox | SUV AWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal,Automatic Transmission Case Plug (O Ring) (15.41Mm O.D.)
Part Number: 24220722
$5.24 MSRP: $8.24
You Save: $3.00 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Transmission Case
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Equinox | SS SUV AWD, SS SUV FWD, SUV AWD, SUV FWD, SUV LT AWD, SUV LT FWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Seal, Automatic Transmission Case (O Ring) (Rear Accumulator, To, Case)
Part Number: 24264987
$0.76 MSRP: $1.21
You Save: $0.45 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, A/Trns Case (O Ring) (Rear Accum, To, Case)
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022 Chevrolet Equinox | 4 DOOR LT, 4 DOOR LTZ | 4 Cyl 2.0L
- 2018-2020 Chevrolet Equinox | 4 DOOR LT, 4 DOOR LTZ | 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal, Power Transfer U Intermediate Drive Shaft To Input S
Part Number: 23349897
$25.08 MSRP: $39.99
You Save: $14.91 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Pwr Trfer U Inter Drv Shf To Input S
- Replaced by: 86506586
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Seal, Power Transfer U Input Shaft
Part Number: 23349898
$26.97 MSRP: $44.63
You Save: $17.66 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Pwr Trfer U Input Shf; Input Shaft Seal
- Replaced by: 86506587
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | 4 DOOR BASE , 4 DOOR LT , 4 DOOR LTZ | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L

| Page 1 of 2 |Next >

1-20 of 25 Results

Chevrolet Equinox Transfer Case Seal

The Transfer Case Seal for the Chevrolet Equinox keeps the all-wheel drive system healthy by locking lubricants inside the transfer case and keeping your gears cool and smooth. The small circular lip seal is positioned at the point where the driveshaft exits the housing. It wraps around the yoke and has a greased rubber edge. Furthermore, it features a coil spring to maintain tension. This is a simple design. Moreover, the lip seal works efficiently. Similarly, the fluid will not leak out even with the rotary motion of the shaft. When the Transfer Case Seal deteriorates, you will see puddles under the case. The lubricant drops, and damage and overheating of the gears can happen. Thus, replacing the seal promptly is an effective way of protecting the shifting quality and life of the drivetrain. The procedure begins by jacking the vehicle on early models. You then unbolt the driveshaft and pry out the old Equinox Transfer Case Seal. After this, you need to clean the bore, grease, and press a new Transfer Case Seal flush with the housing. Finally, realign the yoke using the marks you made prior to removal. Although they have the same layout as previous year, the Chevrolet Equinox has been updated with rubber compounds that resist heat and groove wear. A properly seated Transfer Case Seal remains centered even if some shaft play begins, ensuring every Equinox delivers quiet power with the durability of a Chevrolet.

Each OEM Chevrolet Equinox Transfer Case Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Equinox Transfer Case Seal Parts Questions & Experts Answers

Seal,Transfer Case Input Shaft (O Ring)
19132943
Q: How to replace the transfer case seal on Chevrolet Equinox?
A:
This procedure applies only to NVG-900 Transfer Cases, as the output shaft seal on the Getrag 760 transfer case is not typically serviced while in the vehicle. Begin by raising the vehicle and securely supporting it on jackstands. Drain the transfer case lubricant, then remove the driveshaft. Mark the relative positions of the pinion, nut, and flange. Use a beam-or dial-type inch-pound torque wrench to determine the torque required to rotate the pinion and record it for later use. Count the number of threads visible between the end of the nut and the end of the pinion shaft, and record that as well. Remove the flange mounting nut using a chain wrench to hold the pinion flange while loosening the locknut. A small puller will be required to remove the companion flange, ensuring it has two bolts that screw into the companion flange. Pry out the seal with a screwdriver or seal removal tool, taking care not to damage the seal bore. Lubricate the lips of the new seal with multi-purpose grease and tap it evenly into position with a seal installation tool or a large socket, ensuring it enters the housing squarely and is tapped to its full depth. Align the mating marks made before disassembly and install the companion flange, tightening the pinion nut if necessary to draw the flange into place. Carefully tighten the nut until the original number of threads are exposed and the marks are aligned. Measure the torque required to rotate the pinion and tighten the nut in small increments until it matches the previously recorded figure. Finally, connect the driveshaft, add the specified lubricant to the transfer case, and lower the vehicle.