How to Rocker Shaft Spring Kit and Valve Stem Oil Seal replacement on 4.3L V6 engine on Chevrolet Tahoe?

To replace the Valve Stem Oil Seals, start by removing the valve cover(s) from the cylinder head(s), and if replacing all seals, remove all spark plugs too. If replacing all seals, go according to firing order (1-6-5-4-3-2) and begin with cylinder number 1 i.e. skip 120 degrees clockwise for each cylinder. Position the piston in that selected cylinder at Top Dead Center on the compression stroke by rotating the crankshaft. For that target cylinder head, remove all rocker arms, pushrods, and support bars. Screw an adapter into the spark plug hole and attach a compressed air source which applies approximately 90 to 100 psi of pressure to retain valves position. Shop rags should be inserted into the holes on top of the cylinder heads to prevent foreign objects from entering into the engine. A removal tool such as a valve spring compressor can help compress retainers together with valve springs thus allowing keepers' elimination. Old Valve Stem Oil Seal is then taken out after getting rid of spring retainer or rotator together with its assembly. Keep the rubber band or tape on hand for holding down the valve stem so that it does not fall out when releasing air pressure later on. While installing, ensure there is no damage on valve stem but it moves freely in guide without sticking inside it. Air pressure should be reapplied to hold down the valve while taking off tape or rubber bands. After applying some engine oil for lubrication purposes around the stem ends of valves install new seals after tapping them gently with a deep socket or tool used for installation of a seal into place, care being taken not to twist or cock these seals in any way at this point also check if garter spring is properly positioned around the top of each seal before proceeding further with the installation process of valve spring and damper if applicable closely-wound spring coils facing towards cylinder head while securing either rotator or retainer for valve spring. Disconnect the air hose, remove the adapter from the spark plug hole, and repeat the process for the remaining cylinders, aligning each piston with TDC on the compression stroke. Finally, reinstall the rocker arms, support bars, and pushrods, followed by the valve cover(s), spark plug(s), and wires, and start and run the engine, checking for any oil leaks or unusual noises from the valve cover area.

Genuine Chevrolet Tahoe Valve Stem Oil Seal

Engine Valve Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Valve Stem Oil Seals found

View related parts
Chevrolet Tahoe Seal Kit,Exhaust Valve Stem Oil
Part Number: 12482062
$41.81 MSRP: $69.18
You Save: $27.37 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Valve; Valve Seal, Valve Spring
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2014 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L, 8 Cyl 6.0L Flex
View related parts
Chevrolet Tahoe Seal Kit,Intake Valve Stem Oil
Part Number: 12482063
$38.13 MSRP: $63.11
You Save: $24.98 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Valve; Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2014 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L, 8 Cyl 6.0L Flex
View related parts
Chevrolet Tahoe Seal, Exh Vlv Stem Oil
Part Number: 12689006
$5.23 MSRP: $8.65
You Save: $3.42 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Seal
- Replaces: 12645472
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2024 Chevrolet Tahoe | 1500 4 DOOR UTILITY, 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Int Vlv Stem Oil
Part Number: 12689007
$6.14 MSRP: $9.46
You Save: $3.32 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Seal
- Replaces: 12645473
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2024 Chevrolet Tahoe | 1500 4 DOOR UTILITY, 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal,Valve Stem Oil
Part Number: 10212810
$5.18 MSRP: $7.97
You Save: $2.79 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Valve; Valve Seal, Valve Seal Kit
- Replaces: 00460483, 460483
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal Kit,Exhaust Valve Stem Oil
Part Number: 12457652
$18.08 MSRP: $29.92
You Save: $11.84 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Valve; Valve Seal
- Replaces: 12560189
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L
View related parts
Chevrolet Tahoe Seal Kit,Valve Stem Oil
Part Number: 12533586
$24.27 MSRP: $37.35
You Save: $13.08 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Valve; Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L
View related parts
Chevrolet Tahoe Seal, Exhaust Valve Stem Oil
Part Number: 23502552
$13.05
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Valve; Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 6.5L Diesel
View related parts
Chevrolet Tahoe Seal,Valve Stem Oil
Part Number: 10214034
$1.77 MSRP: $2.72
You Save: $0.95 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Valve; Seal Ring, Valve Seal, Valve Seal O-Ring
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L, 8 Cyl 6.5L Diesel
View related parts
Chevrolet Tahoe Seal Assembly, Vlv Stem Oil
Part Number: 55484799
$2.79 MSRP: $4.32
You Save: $1.53 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Tahoe | 4 DOOR 1/2 TON | 6 Cyl 3.0L Diesel
View related parts
Chevrolet Tahoe Seal, Exhaust Valve Stem Oil
Part Number: 12564852
Product Specifications
- Other Name: SEAL, Engine Valve; Valve Seal
- Replaces: 12558674
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal Kit,Valve Stem Oil
Part Number: 12511890
Product Specifications
- Other Name: SEAL KIT, Engine Valve; Valve Seal, Valve Seal Kit
- Replaces: 14033546, 10132715
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal, Exhaust Valve Stem Oil
Part Number: 10147883
Product Specifications
- Other Name: SEAL, Engine Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal, Exhaust Valve Stem Oil
Part Number: 10147882
Product Specifications
- Other Name: SEAL, Engine Valve; Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal, Exhaust Valve (.015 Outside)
Part Number: 10168534
Product Specifications
- Other Name: SEAL, Engine Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal Assembly, Inlet Valve Stem Oil .030" Oversize (Free Of Asbestos)
Part Number: 14037716
Product Specifications
- Other Name: SEAL, Engine Valve; Valve Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal Assembly, Intake Valve Stem Oil .015" Oversize (Free Of Asbestos)
Part Number: 14037715
Product Specifications
- Other Name: SEAL, Engine Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L

Chevrolet Tahoe Valve Stem Oil Seal

The Chevrolet Tahoe Valve Stem Oil Seal is crucial because it prevents engine oil from leaking past the valve stem into the combustion chamber. This improves power and reduces smoke production. The Valve Stem Oil Seal fits around the moving valve stem inside every cylinder head, meters a thin film of oil to the guide, and scrapes away excess oil before it can be sucked through the intake or pushed through the exhaust. Regardless of whether the SUV is using an overhead valve block that uses lifters and pushrods or a newer overhead cam layout, the Valve Stem Oil Seal works the same. It is positioned at the very top of the chamber and is the final barricade separating the pressurized oil from the burning air-fuel mix. The Valve Stem Oil Seal stops the oil from getting into the chambers. This promotes stable compression within the cylinders of a car. Further, it prevents the buildup of carbon and lessens blue tailpipe haze that can fail emissions tests. The Valve Stem Oil Seal can harden or shrink due to high mileage, heat, and worn valvetrain parts. Consequently, drip through occurs that mimics weak springs or burnt valves. So a Chevrolet Tahoe owner from any model year must watch for startup smoke as an early warning. A new Chevrolet part, when freshly replaced, restores the correct oil control, protects the catalytic converters, and helps the Tahoe engine function at peak efficiency.

Each OEM Chevrolet Tahoe Valve Stem Oil Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Tahoe Valve Stem Oil Seal Parts Questions & Experts Answers

Seal Kit,Exhaust Valve Stem Oil
12482062
Q: How to Rocker Shaft Spring Kit and Valve Stem Oil Seal replacement on 4.3L V6 engine on Chevrolet Tahoe?
A:
To replace the Valve Stem Oil Seals, start by removing the valve cover(s) from the cylinder head(s), and if replacing all seals, remove all spark plugs too. If replacing all seals, go according to firing order (1-6-5-4-3-2) and begin with cylinder number 1 i.e. skip 120 degrees clockwise for each cylinder. Position the piston in that selected cylinder at Top Dead Center on the compression stroke by rotating the crankshaft. For that target cylinder head, remove all rocker arms, pushrods, and support bars. Screw an adapter into the spark plug hole and attach a compressed air source which applies approximately 90 to 100 psi of pressure to retain valves position. Shop rags should be inserted into the holes on top of the cylinder heads to prevent foreign objects from entering into the engine. A removal tool such as a valve spring compressor can help compress retainers together with valve springs thus allowing keepers' elimination. Old Valve Stem Oil Seal is then taken out after getting rid of spring retainer or rotator together with its assembly. Keep the rubber band or tape on hand for holding down the valve stem so that it does not fall out when releasing air pressure later on. While installing, ensure there is no damage on valve stem but it moves freely in guide without sticking inside it. Air pressure should be reapplied to hold down the valve while taking off tape or rubber bands. After applying some engine oil for lubrication purposes around the stem ends of valves install new seals after tapping them gently with a deep socket or tool used for installation of a seal into place, care being taken not to twist or cock these seals in any way at this point also check if garter spring is properly positioned around the top of each seal before proceeding further with the installation process of valve spring and damper if applicable closely-wound spring coils facing towards cylinder head while securing either rotator or retainer for valve spring. Disconnect the air hose, remove the adapter from the spark plug hole, and repeat the process for the remaining cylinders, aligning each piston with TDC on the compression stroke. Finally, reinstall the rocker arms, support bars, and pushrods, followed by the valve cover(s), spark plug(s), and wires, and start and run the engine, checking for any oil leaks or unusual noises from the valve cover area.