My Garage
My Account
Cart
Genuine Pontiac Firebird Throttle Body
Fuel Injection Throttle Body- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
24 Throttle Bodies found
Pontiac Firebird Tbi Throttle Body Kit
Part Number: 17112067$201.81 MSRP: $434.76You Save: $232.95 (54%)
| Page 1 of 2 |Next >
1-20 of 24 Results
Pontiac Firebird Throttle Body
The Throttle Body in Pontiac Firebird vehicles allows a direct control on the amount of air that can get into the engine and therefore performance ability and efficiency. Located between the air cleaner and intake manifold it has a butterfly valve that opens in proportion to the accelerator pedal position so as to admit more air into the engine. This action is accompanied with different sensors that are in touch with the Powertrain Control Module (PCM) for the purpose of modifying the fuel injection. The Throttle Bodies also evolved as the years went on, using Throttle Body Injection TBI and today's sophisticated multi-port fuel injection. Some earlier model Firebirds used TBI units which are relatively basic and housed within a single unit, whereas later model Firebirds usually use Electronic Throttle Control (ETC) systems for improved sensitivity that also interconnect with other safety functions. A shift from mechanical linkages to electronic systems represents a trend improvement on the Throttle Body for the Pontiac Firebird sequence.
Each OEM Pontiac Firebird Throttle Body we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Pontiac Firebird Throttle Body Parts Questions & Experts Answers
- Q: What is the proper procedure for replacing fuel injectors, throttle position sensor, Idle Control Valve and throttle body assembly on Pontiac Firebird?A: Open the fuel injector rail pressure release valve, then disconnect the cable from the negative terminal of the battery before turning off the anti-hood jacking system and on Delco Loe II audio system, do the same. Covers and plates, air cleaner housing assembly, EOx20EGC1100 adapter, and gaskets should be removed. The Fuel Pressure Regulator is incorporated in the fuel meter cover and if the assembly is being worked on or the fuel meter cover is being changed, the entire holder has to be replaced. Disconnect the electrical connectors from the fuel injectors, remove the fuel meter cover screws and then remove the fuel meter cover. Take out the gaskets and clean out all previous gasket material used as they are not to be reused. Clean the metal casing and any lenses which are on the top or sides of the cover if it is located in a retail store, replace the gaskets and seals if required. When refitting the fuel meter cover use the Loctite 262 on the screws before reconnecting the electrical connectors to the injector and the negative terminal of the battery. Ensure to do the check with the engine off, but with the ignition on prior to reinstalling the air cleaner assembly. When replacing fuel injectors ensure that they are of the exact part number, disconnect the connectors and finally dismantle the fuel meter cover assembly using the special spanner but without having to remove the gasket. Remove the injectors, remove the O-rings and filters then check for contamination. Before you fit the new O-rings it is important to ensure that they are soaked in automatic transmission fluid. After putting the injectors properly in place, equally replace the fuel meter cover. By doing so you will ensure that there are no more leaks after having reconnected the battery. For the throttle position sensor, one should remove this component from the throttle body but should not use any liquid cleaners for the same and then fix the lever in the right manner when reinstalling this component. For the idle air control valve, as given in the procedure disconnect the connector then disconnect the valve, remove the old gasket and make sure that the new one fits correctly. This pintle should be adjusted as required prior to being reattached. To disassemble the fuel meter body assembly, first, disconnect the connectors, then uninstall the assembly and undo the fuel lines connection also note the position of the nut for reassembly. Ensure that gaskets have been replaced well and all joints are well tightened. For the throttle body assembly there should be disconnecting of all connectors, removal of linkages and the throttle body together with removal of the gasket will also be dumped. Wash the assembly without immersing any delicate parts, look for signs of wear and tear and replace the IAC valve and TPS. Tighten all the joints, check that there is no interference of the accelerator pedal, and connect the negative terminal of the battery. They are to check for oil leaks, warm up the engine and also to adjust the idle speed. When you find it necessary, then follow the laid down procedures of synchronization and alignment.
Related Pontiac Firebird Parts
Browse by Year
2002 Throttle Body 2001 Throttle Body 2000 Throttle Body 1999 Throttle Body 1998 Throttle Body 1997 Throttle Body 1996 Throttle Body 1995 Throttle Body 1994 Throttle Body 1993 Throttle Body 1992 Throttle Body 1991 Throttle Body 1990 Throttle Body 1989 Throttle Body 1988 Throttle Body 1987 Throttle Body 1986 Throttle Body 1985 Throttle Body