Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 23145777 Rear Axle Assembly. It is sometimes referred to as Chevrolet Axle Shaft. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific Chevrolet Tahoe models.
Affordable, reliable and built to last, GM part # 23145777 Rear Axle Assembly stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed Chevrolet parts information, click here.
×
My Garage
My Account
My Cart
Make sure this part fits your vehicle
Chevrolet 23145777 Rear Axle Assembly
2010-2014 Chevrolet Tahoe
- Part DescriptionAxle Assembly, Rear
- PositionRear
- Replaces20937809, 23129848, 22968249, 25988369, 22874926
- ManufacturerGeneral Motors
- Manufacturer's NotesThis part is discontinued.
Product Specifications
Brand Genuine Chevrolet Manufacturer Part Number 23145777 Part Description Axle Assembly, Rear Position Rear Condition New Fitment Type Direct Replacement Replaces 20937809, 23129848, 22968249, 25988369, 22874926 Manufacturer General Motors SKU 23145777 Warranty This genuine GM part is guaranteed by GM's factory warranty. Shipping & Return Shipping Policy Return Policy Warning: California’s Proposition 65Vehicle Fitment
Year Make Model Engine Important vehicle option details 2010-2014 Chevrolet Tahoe 8 Cyl 5.3L Flex, 8 Cyl 6.0L Flex 4 DOOR 1/2 TON
Customer Questions & Answers
- Q:I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
- A:You can Select Your Vehicle to check if 23145777 fits your vehicle.Posted by GMPartsGiant Specialist
- Q:How do you remove and install components in the front differential for AWD systems for the 2010 GMC Yukon? Posted by Customer
- A:To remove and install components in the front differential for AWD systems, follow these steps: Remove the stabilizer bar link and, if applicable, the front shock absorber. Unbolt the right driveaxle from the axleshaft flange, supporting it properly. Support the differential carrier with a floor jack and a block of wood. Remove nuts attaching the axle shaft to its support bracket and the bolts securing the axle shaft flange to the differential carrier. Use a brass punch and hammer to separate the axle shaft from the differential case side gear. Remove the inner axle shaft assembly and axle shaft. Replace the inner seal and bearing with a special tool, then apply RTV sealant to the differential sealing surface and install the inner axle shaft housing assembly. Install the axle shaft to the support bracket and align the splines with the differential side gear. Tap the axle shaft with a mallet until the ring (clip) aligns with the groove in the differential case side gear. Install the axle shaft to the inner flange and tighten the bolts. Reinstall the stabilizer link, fill the differential with lubricant, install the differential carrier splash shield, and finally, install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts, and check for proper operation.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
- Q:What should be done before installing the driveaxle for the 2008 GMC Yukon? Posted by Customer
- A:Before installing the driveaxle, the splines on the stub shaft should be lubricated with multi-purpose grease.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
- Q:What should be done if a CV joint boot is damaged for the 2010 GMC Yukon? Posted by Customer
- A:If a boot is damaged, the CV joint can be disassembled and cleaned, but if any parts are damaged, the entire driveaxle assembly must be replaced as a unit.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
- Q:What type of front axle assembly is used in the 2012 GMC Yukon? Posted by Customer
- A:4WD models use a fully independent front axle assembly.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
- Q:What steps should be followed for the 2011 GMC Yukon? Posted by Customer
- A:For coil spring models, the links for the electronic suspension control sensors should be detached, followed by detaching the track bar from the rear axle. The stabilizer bar, coil springs, and upper and lower trailing arms should be disconnected from the axle assembly. Finally, the jack can be lowered under the differential to remove the rear axle assembly.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
- Q:What should be done before removing a semi-floating axle shaft for the 2008 GMC Yukon? Posted by Customer
- A:Before removing a semi-floating axle shaft, you should loosen the rear wheel lug nuts and raise the vehicle on jackstands.Posted by GMPartsGiant Specialist
- See expert answers on similar Axle Shaft
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!
Genuine GM Part 23145777, the Right Choice
Why choose GM Parts Giant
- Dedicated Service
Your complete satisfaction is our #1 goal
- Lowest Prices
Best deals on genuine OE parts from dealerships
- Fast Delivery
Orders are processed and delivered promptly