How to replace and install the front Wheel Bearing and Wheel Seal of 4WD Chevrolet Avalanche?

To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left axle shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.

Genuine Chevrolet Avalanche Wheel Seal

Wheel Axle Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Wheel Seals found

View related parts
Chevrolet Avalanche Seal Assembly, Front Drive Axle Inner Shaft
Part Number: 22761722
$22.33 MSRP: $38.51
You Save: $16.18 (43%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Axle; Output Shaft Seal
- Position: Front Inner
- Replaces: 12471591, 12471682, 15801507, 12479012, 26059623
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2013 Chevrolet Avalanche | 1/2 TON | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L
View related parts
Chevrolet Avalanche Seal,Rear Axle Shaft
Part Number: 15823962
$29.09 MSRP: $54.88
You Save: $25.79 (47%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SEAL, Rear Wheel Bearing Oil; Axle Seal, Hub Seal
- Position: Rear
- Replaces: 15007008, 26061024
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Avalanche | 3/4 TON | 8 Cyl 8.1L
View related parts
Chevrolet Avalanche Seal,Front Wheel Drive Shaft
Part Number: 19169124
$11.11 MSRP: $18.41
You Save: $7.30 (40%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Axle; Output Shaft Seal
- Position: Front
- Replaces: 12471683, 12471592, 12479155, 26059624
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Avalanche | 3/4 TON | 8 Cyl 8.1L
View related parts
Chevrolet Avalanche Seal, Front Wheel Hub (O Ring)
Part Number: 15017464
$6.32 MSRP: $11.92
You Save: $5.60 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Wheel Bearing; Front Hub Seal, Hub & Bearing Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Avalanche | 3/4 TON | 8 Cyl 8.1L
View related parts
Chevrolet Avalanche Seal,Propeller Shaft Front Slip Yoke Oil
Part Number: 8673526
$6.78 MSRP: $10.80
You Save: $4.02 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SEAL, Transmission Rear Main Bearing; Extension Housing Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Chevrolet Avalanche | 1/2 TON | 8 Cyl 5.3L, 8 Cyl 5.3L Flex
View related parts
Chevrolet Avalanche Seal,Rear Axle Shaft
Part Number: 12471686
$11.78 MSRP: $22.22
You Save: $10.44 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Rear Wheel Bearing Oil
- Position: Rear
- Replaces: 15522060, 26037309
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2013 Chevrolet Avalanche | 1/2 TON | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L

Chevrolet Avalanche Wheel Seal

The Wheel Seal of Chevrolet Avalanche vehicles essentially works to shield the hub and bearing from unfavorable conditions such as rough terrains, rocks, dirt and other related substances. Again, adequate lubrication is necessary to avoid overheating, and the brittleness of the materials used in the component. It is advised to inspect for ruptures and cracks in order to achieve the highest efficiency of the equipment. Both front and rear inner and out wheel seals are possible or you could go for complete sets from acknowledged manufactures like the Motorcraft and the Timken etc. Such high-grade materials ensure a spot on truck, car or even SUVS without compromising the wheel bearing assembly.

Each OEM Chevrolet Avalanche Wheel Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Avalanche Wheel Seal Parts Questions & Experts Answers

Seal,Propeller Shaft Front Slip Yoke Oil
8673526
Q: How to replace and install the front Wheel Bearing and Wheel Seal of 4WD Chevrolet Avalanche?
A:
To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left Axle Shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.