How to remove the Canister Purge Valves and Vapor Canister on Chevrolet Cobalt?

To remove the EVAP canister purge solenoid, turn off the ignition and locate the solenoid. Disconnect the electrical connector and purge line fittings, and cap the lines. Remove the mounting bracket bolt and separate the solenoid. For the vent solenoid, raise the vehicle's rear and disconnect the electrical connector. Remove the mounting bolt, lower the canister, and rotate the solenoid counterclockwise to remove. To remove the EVAP canister, disconnect the hoses. For the fuel tank pressure sensor, raise the vehicle, remove the fuel tank, and disconnect the sensor's electrical connector. Pry under the sensor to remove it. Installation is the reverse of removal.

Genuine Chevrolet Cobalt Canister Purge Valves

Fuel Tank Evaporator Purge Control Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Canister Purge Valves found

View related parts
Chevrolet Cobalt Evap Emission Canister Purge Solenoid Valve Assembly
Part Number: 12597567
$33.14 MSRP: $67.60
You Save: $34.46 (51%)
ADD TO CART
Product Specifications
- Other Name: VALVE, Fuel Tank Evaporator/Purge Control
- Replaced by: 12735397
- Replaces: 12606684, 12597566, 12570469, 12597341
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | 2 DOOR, 4 DOOR, LEVEL 4 PERFORMANCE (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 4 DOOR, LEVEL ONE (LS) 2 DOOR, LEVEL ONE (LS) 4 DOOR, LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR, LEVEL TWO (LT) 2 DOOR, LEVEL TWO (LT) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Solenoid Assembly, Evap Emis Cnstr Vent Vlv
Part Number: 84524035
$21.63 MSRP: $40.82
You Save: $19.19 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 42933353
- Replaces: 22865590, 15788844, 17114055, 21993142, 20924750, 25321964, 25932573
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | 2 DOOR, 4 DOOR, LEVEL 4 PERFORMANCE (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 4 DOOR, LEVEL ONE (LS) 2 DOOR, LEVEL ONE (LS) 4 DOOR, LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR, LEVEL TWO (LT) 2 DOOR, LEVEL TWO (LT) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Evap Emission Canister Purge Solenoid Valve Assembly
Part Number: 12592015
$31.69 MSRP: $59.80
You Save: $28.11 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: VALVE, Fuel Tank Evaporator/Purge Control
- Replaced by: 12735400
- Replaces: 12608378
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 4 DOOR | 4 Cyl 2.0L

Chevrolet Cobalt Canister Purge Valves

Chevrolet Cobalt Canister Purge Valves are designed to trap fuel vapors and route them into the engine instead of allowing them to escape into the atmosphere. They help reduce harmful hydrocarbons and promote clean combustion in the engine. A compact solenoid valve opens when the engine control module sees the load and temperature are right. Then vacuum draws stored fumes from the charcoal canister into the intake. The vapors then burn with the normal air fuel mix. This shows how Canister Purge Valves link emission control directly to engine operation. Before, vented caps were utilized to let vapor escape, but now the sealed system has smart Canister Purge Valves to pass strict smog laws without hurting drivability. Over the subsequent years of Cobalt, Chevrolet kept the electronically controlled solenoid design. Hence, owners mostly observe minor changes in the connector or the calibration over the years rather than seeing entirely different styles of valve. Regardless of revision, all Canister Purge Valves are normally closed when the engine is idle but cycle on command to maintain proper tank pressure and prevent saturation of the canister. Reliable Canister Purge Valves also allow for onboard leak checks by allowing the module to pull tank vacuum, illuminating the warning lamp if pressure fails to drop. All Chevrolet Cobalt's come with features that make them run cleaner and use up less fuel while complying with emissions standards.

Each OEM Chevrolet Cobalt Canister Purge Valves we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Cobalt Canister Purge Valves Parts Questions & Experts Answers

Evap Emission Canister Purge Solenoid Valve Assembly
12597567
Q: How to remove the Canister Purge Valves and Vapor Canister on Chevrolet Cobalt?
A:
To remove the EVAP canister purge solenoid, turn off the ignition and locate the solenoid. Disconnect the electrical connector and purge line fittings, and cap the lines. Remove the mounting bracket bolt and separate the solenoid. For the vent solenoid, raise the vehicle's rear and disconnect the electrical connector. Remove the mounting bolt, lower the canister, and rotate the solenoid counterclockwise to remove. To remove the EVAP canister, disconnect the hoses. For the fuel tank pressure sensor, raise the vehicle, remove the fuel tank, and disconnect the sensor's electrical connector. Pry under the sensor to remove it. Installation is the reverse of removal.