My Garage
My Account
Cart
Genuine Chevrolet Express Intake Manifold Temperature Sensor
Air Intake Temperature Sensor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
1 Intake Manifold Temperature Sensor found
Chevrolet Express Sensor,Intake Air Temperature
Part Number: 12160244$16.48 MSRP: $27.28You Save: $10.80 (40%)Ships in 1-3 Business Days
Chevrolet Express Intake Manifold Temperature Sensor
The Chevrolet Express Intake Manifold Temperature Sensor helps the engine computer deliver the right air fuel blend by reporting incoming air conditions. This sensor is located in the intake stream, which works with the mass air flow meter so the PCM can fine-tune injector pulse width across idle, cruise, and full-throttle events. When the Intake Manifold Temperature Sensor or its companion airflow sensor become coated with dirt, heat readings misfire, and the module miscalculates how much air gets applied. Hesitation, stalling, or a lean surge may occur. Earlier Chevrolet vans were equipped with a straightforward thermistor style Intake Manifold Temperature Sensor, while later Express models boast a faster-acting hot wire design featuring improved accuracy and contamination resistance that transmits fresher data. Regardless of those differences, every Intake Manifold Temperature Sensor has the same job. It provides temperature readings to the PCM, which take place in less than a second. This allows for quick detection of unmetered air leaks and maintenance of the air-fuel ratio. As a result, this tiny component plays a huge role in a Chevrolet Express' workings. The Intake Manifold Temperature Sensor is essential for optimal engine performance.
Each OEM Chevrolet Express Intake Manifold Temperature Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet Express Intake Manifold Temperature Sensor Parts Questions & Experts Answers
- Q: How to remove and install the Intake Manifold Temperature Sensor on Chevrolet Express?A:Take the cable away from the negative battery terminal. This sensor is found on the air intake duct for 4.3L V6 and 5.0L, 5.7L, and 7.4L V8 engines as indicated below. Take off the Intake Manifold Temperature Sensor's electrical connector. In case of a vehicle with a 4.3L V8 or a 5.0L, 5.7L, or 7.4L V8 engine, you should just disconnect the electrical connector and pull it out of its mounting hole in the intake duct by holding firmly onto it. Grasp it firmly and carefully remove the Intake Manifold Temperature Sensor from the air intake duct of your vehicle with firmness and care to avoid any damage that might be caused to either the sensor or the air intake duct itself when removing it out of there by pulling gently but forcefully against resistance or twisting one way then another before lifting up off its mount point near where the other wires are attached nearby; you can also use pliers if necessary but make sure not to break anything while doing so! The Intake Manifold Temperature Sensor is removed by holding it tightly and pulling out of an air intake duct. All cracks, tears, and deteriorations are inspected around an Intake Manifold Temperature Sensor mounting hole in an air intake duct. Replace the intake duct if there is any damage on the mounting hole. Installation is done in reverse order as compared to removal operations: for example, what was removed first should now be installed last while what was installed last becomes the first part that should be removed prior to the installation process beginning all over again at each step along the way until everything has been put into the correct place exactly where needed which would require following the proper sequence according to the plan provided here within these instructions given previously such as referring back through one page only instead of going through the whole book all at once without any reference points whatsoever except those mentioned above concerning the order followed during the disassembly stage according to the schedule prepared from the original manufacturer's manual, etc. This is true for 4.8L, 5.3L, and 6.0L V8 engines wherein the Intake Manifold Temperature Sensor is one of the parts of the Mass Air Flow (MAF) sensor.
