How to replace the Hood Cable and Hood Latch on Chevrolet Monte Carlo?

To replace the latch, first, discharge the bolts holding the radiator cover plate allowing it to be removed. Mark around the latch while indenting it so that it can easily fit the positions when reinstalling it, then remove the latch retaining bolts from the radiator support as well as the latch. Subsequently, you have to let go of the hook of the hood release cable that corresponds to the latch assembly. For the cable, cut off from the latch assembly and then fit a wire of stiffness to the end of the cable and give path back to the firewall and then remove all of the retaining clips. In the passenger compartment unscrew the hood cable from the hood release lever and retract the old cable into the compartment until a stiff wire from the end is seen. This allows a grommet to be placed in the cable hole in the firewall; if replacing the cable simply make sure a new grommet is used and the old one discarded. Remove the old cable from the wire and fit the new cable and pass the wire through the hole provided at the engine compartment. Last of all, it is straining the grommet from inside the car interior while making sure it fits in the hole of the firewall properly.

Genuine Chevrolet Monte Carlo Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Hood Cables found

View related parts
Chevrolet Monte Carlo Hood Primary Latch Release Cable Assembly
Part Number: 10311086
$67.08 MSRP: $100.29
You Save: $33.21 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CABLE, Hood Latch; Release Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Handle Assembly, Hood Primary Latch Release Cable (Less Cable)
Part Number: 10289335
Product Specifications
- Other Name: HANDLE, Hood Latch; Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Handle Assembly, Hood Primary Latch Release Cable
Part Number: 10285029
Product Specifications
- Other Name: HANDLE, Hood Latch; Handle, Release Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Hood Primary Latch Release Cable Assembly
Part Number: 10407412
Product Specifications
- Other Name: CABLE, Hood Latch; Release Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Handle Assembly, Hood Primary Latch Release
Part Number: 10186999
Product Specifications
- Other Name: HANDLE, Hood Latch; Release Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L

Chevrolet Monte Carlo Hood Cable

The Chevrolet Monte Carlo Hood Cable is an important part of the hood that connects the release lever in the cabin to the twin latches holding the hood. It allows the driver to pop the hood open quickly for inspection or repairs. This flexible, steel-cored line is connected from the dashboard handle to a junction beneath the hood. Then it branches off to each latch so that one pull can trigger simultaneous release on either side. Over years of road grime, heat, and moisture, the Hood Cable housing can develop cracks and allow water in, which can cause corrosion or stretching of the inner wire, leaving the hood stuck shut at the worst time. To remedy this, Chevrolet opted for a simple design. After all, a direct mechanical pull offers reliable action without electronics. Moreover, diagnosis should be simple, as it is either moving the latch or not. The design of the Hood Cable of the Monte Carlo has been consistent throughout its production history, so there was no comparison of different generations or special versions and only made use of material improvements for durability. Over time, the Hood Cable can become frayed. Inspecting the Hood Cable regularly and replacing it if frayed ensures every owner has safe, easy access to vital engine components on the Chevrolet Monte Carlo.

Each OEM Chevrolet Monte Carlo Hood Cable we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Monte Carlo Hood Cable Parts Questions & Experts Answers

Hood Primary Latch Release Cable Assembly
10311086
Q: How to replace the Hood Cable and Hood Latch on Chevrolet Monte Carlo?
A:
To replace the latch, first, discharge the bolts holding the radiator cover plate allowing it to be removed. Mark around the latch while indenting it so that it can easily fit the positions when reinstalling it, then remove the latch retaining bolts from the radiator support as well as the latch. Subsequently, you have to let go of the hook of the hood release cable that corresponds to the latch assembly. For the cable, cut off from the latch assembly and then fit a wire of stiffness to the end of the cable and give path back to the firewall and then remove all of the retaining clips. In the passenger compartment unscrew the hood cable from the hood release lever and retract the old cable into the compartment until a stiff wire from the end is seen. This allows a grommet to be placed in the cable hole in the firewall; if replacing the cable simply make sure a new grommet is used and the old one discarded. Remove the old cable from the wire and fit the new cable and pass the wire through the hole provided at the engine compartment. Last of all, it is straining the grommet from inside the car interior while making sure it fits in the hole of the firewall properly.