How to replace the front Crankshaft Seal in inline engine on GMC Canyon?

Even with this setup version, be careful not to damage the crankshaft threads; if you have a hard time removing the pulley, it is advisable to suspend operation and get the special tools for crankshaft or consult a professional mechanic. The crankshaft end surface as well as the engine front cover have to be shielded. Special tools necessary are puller which can be obtained from GM as # J-44226 or equivalent, Crank shaft end protector can also be got from GM as #J-41816-2 or its equivalent, Pulley installer obtainable from GM as J-41478 or the equivalent and the seal installer can be got from GM as #J-44218 or its equivalent. On the other hand, we have a three jaw puller, deep socket for the crank shaft nose, and a thread pressed tool that screws into the crank shaft. The crank pulley is designed in such a way that it does not have a fixed position that it has to be installed in, and a new shim must always be placed each time the pulley is replaced. To pull the pulley you first have to remove the radiator and driving belt, and then unscrew the torque converter access plug in the pan to prevent the crank shaft from spinning while turning the crank shaft pulley bolt. Once the bolt is out, fit on the crankshaft end protector, fit on the puller and gently pull out the pulley and shim with the puller, which should grip only the hub of the pulley. You have to pry the oil seal out using the right tool for the purpose is among the essential steps. At installation check the pulley for its condition, lubricate the outside of the oil seal, not the inside, and install it into the front cover until flush with the surface. Put a new pulley shim on top of the crankshaft sprocket, jack up your vehicle safely, position the pulley on the crankshaft, and then settle it with the installer tool, do not use a hammer in the process. Last, do away with the installer tool, apply a pulley washer and bolt, then turn several times while someone else applies pressure using a screwdriver at the ring gear teeth in the reverse of the removal process.

Genuine GMC Canyon Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Crankshaft Seals found

View related parts
GMC Canyon Seal Assembly, Crankshaft Rear Oil
Part Number: 12591866
$22.86 MSRP: $39.10
You Save: $16.24 (42%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Replaces: 90298408, 90325572, 90280462, 90354378
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | CREW CAB - 5'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L
View related parts
GMC Canyon Seal Assembly, Crankshaft Front Oil
Part Number: 12626923
$19.78 MSRP: $32.73
You Save: $12.95 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal; Crankshaft Seal, Front Crank Seal, Front Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | CREW CAB - 5'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L
View related parts
GMC Canyon Seal Kit,Crankshaft Front Oil
Part Number: 89017622
$17.03 MSRP: $28.18
You Save: $11.15 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Rear Main Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.8L, 4 Cyl 2.9L, 5 Cyl 3.5L, 5 Cyl 3.7L
View related parts
GMC Canyon Seal Kit,Crankshaft Rear Oil
Part Number: 89060436
$24.13 MSRP: $39.93
You Save: $15.80 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Rear Main Bearing; Crankshaft Seal, Rear Main Seal
- Position: Rear
- Replaces: 12550574, 12585671, 89018162
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 8 Cyl 5.3L
View related parts
GMC Canyon Seal,Crankshaft Front Oil
Part Number: 12608750
$9.18 MSRP: $15.19
You Save: $6.01 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal
- Position: Front
- Replaces: 12592355
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 6 Cyl 3.6L
View related parts
GMC Canyon Seal Assembly, Crankshaft Rear Oil
Part Number: 12637710
$42.75 MSRP: $73.74
You Save: $30.99 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal, Rear Main Seal Retainer
- Position: Rear
- Replaces: 12608748, 12620955, 12592243, 12592242
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 6 Cyl 3.6L
View related parts
GMC Canyon Seal Kit,Crankshaft Rear Oil
Part Number: 89018205
$22.41 MSRP: $37.09
You Save: $14.68 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Replaces: 12568124
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.8L, 4 Cyl 2.9L, 5 Cyl 3.5L, 5 Cyl 3.7L
View related parts
GMC Canyon Seal, Crankshaft Front Oil
Part Number: 12642203
$12.17 MSRP: $22.96
You Save: $10.79 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal; Front Crank Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.8L Diesel
View related parts
GMC Canyon Seal, Crankshaft Rear Oil
Part Number: 12625417
$20.54 MSRP: $34.01
You Save: $13.47 (40%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.8L Diesel
View related parts
GMC Canyon Seal Assembly, Crankshaft Front Oil
Part Number: 12654010
$4.66 MSRP: $7.72
You Save: $3.06 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal; Crankshaft Seal, Front Crank Seal, Front Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 6 Cyl 3.6L
View related parts
GMC Canyon Seal, Cr/Shf Frt (O Ring)
Part Number: 12693989
$1.35 MSRP: $2.16
You Save: $0.81 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Seal, Front Crank Seal, Front Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB SLE -5'2" BOX, CRW CAB SPORT-5'2" BOX(I), SLT CREW CAB - 5'2" BOX, SPORT CREW-5'2" BOX | 4 Cyl 2.7L

GMC Canyon Crankshaft Seal

It is part of the diesel engine GMC Canyon common rail system, it is situated at the front part of the engine and has a function of sealing the crankcase to ensure that oil does not leak out. Usually manufactured from metal and rubber this round seal is a key element in ensuring the provision of lubrication to the engine hence minimizing wear by reducing friction on the engine's components. Clearly, a GMC Canyon's Crankshaft Seal may get spoiled with constant use over time or when it is of high mileage, there may be signs like oil leaks. While the basic design remains consistent, variations in materials or construction may exist across different model years, but the primary function of the Crankshaft Seal remains the same: so that it is capable to run the car's engine correctly without causing a loss of oil.

Each OEM GMC Canyon Crankshaft Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Canyon Crankshaft Seal Parts Questions & Experts Answers

Seal Kit,Crankshaft Front Oil
89017622
Q: How to replace the front Crankshaft Seal in inline engine on GMC Canyon?
A:
Even with this setup version, be careful not to damage the crankshaft threads; if you have a hard time removing the pulley, it is advisable to suspend operation and get the special tools for crankshaft or consult a professional mechanic. The crankshaft end surface as well as the engine front cover have to be shielded. Special tools necessary are puller which can be obtained from GM as # J-44226 or equivalent, Crank shaft end protector can also be got from GM as #J-41816-2 or its equivalent, Pulley installer obtainable from GM as J-41478 or the equivalent and the seal installer can be got from GM as #J-44218 or its equivalent. On the other hand, we have a three jaw puller, deep socket for the crank shaft nose, and a thread pressed tool that screws into the crank shaft. The crank pulley is designed in such a way that it does not have a fixed position that it has to be installed in, and a new shim must always be placed each time the pulley is replaced. To pull the pulley you first have to remove the radiator and driving belt, and then unscrew the torque converter access plug in the pan to prevent the crank shaft from spinning while turning the crank shaft pulley bolt. Once the bolt is out, fit on the crankshaft end protector, fit on the puller and gently pull out the pulley and shim with the puller, which should grip only the hub of the pulley. You have to pry the oil seal out using the right tool for the purpose is among the essential steps. At installation check the pulley for its condition, lubricate the outside of the oil seal, not the inside, and install it into the front cover until flush with the surface. Put a new pulley shim on top of the crankshaft sprocket, jack up your vehicle safely, position the pulley on the crankshaft, and then settle it with the installer tool, do not use a hammer in the process. Last, do away with the installer tool, apply a pulley washer and bolt, then turn several times while someone else applies pressure using a screwdriver at the ring gear teeth in the reverse of the removal process.