How to replace the front crankshaft seal on 2.2L four cylinder engine on GMC Jimmy?

Remove the cable from the negative battery terminal. Remove the drive belt. Raise the vehicle and securely place it on jackstands. Remove the hub retaining bolt. Place a bar through one of the pulley holes and wedge it against the bottom of the front cover to keep the pulley from turning while loosening the pulley bolts. Remove the pulley hub. Use a puller if necessary. Note how the seal is installed-the new one must face the same direction! Carefully pry the Crankshaft Seal out of the cover with a seal puller or a large screwdriver. Be very careful not to distort the cover or scratch the crankshaft! Apply a thin layer of engine oil or multi-purpose grease to the Crankshaft Seal lip and to the outer edge of the new seal. Install the seal in the cover with the lip (open end) facing IN. Drive the seal into place with a large socket and a hammer. Make sure the seal enters the bore squarely and is driven in until the front face is flush with the cover. The seal can also be replaced if the timing chain cover has been removed for other work. Support the cover on a block of wood and drive the seal out from the backside. Install a new seal into the bore. Reinstall the timing chain cover with a bead of RTV sealant applied to the mating surface of the oil pan. Apply a small amount of RTV sealant on the crankshaft Woodruff key. Align the slot in the hub with the crankshaft Woodriff key, then press the hub onto the crankshaft until it bottoms against the crankshaft timing gear. The hub retaining bolt can be used to press the hub into position. Install the crankshaft pulley on the hub. Use a non-hardening thread-locking compound on the bolt threads. Tighten the hub-to-crankshaft bolt. Install the drive belt.

Genuine GMC Jimmy Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Crankshaft Seals found

View related parts
GMC Jimmy Seal,Crankshaft Front Oil
Part Number: 10128316
$20.97 MSRP: $39.56
You Save: $18.59 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Seal,Crankshaft Front Oil
Part Number: 14090906
$21.01 MSRP: $39.63
You Save: $18.62 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal
- Position: Front
- Replaces: 12577710
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
- 1985-1989 GMC Jimmy | 1/2 TON | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
GMC Jimmy Seal,Crankshaft Rear Oil
Part Number: 10088158
$33.43 MSRP: $55.35
You Save: $21.92 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1995 GMC Jimmy | 1/2 TON, 2 DOOR, 4 DOOR | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
GMC Jimmy Seal,Crankshaft Front Oil
Part Number: 10191640
$19.15 MSRP: $36.15
You Save: $17.00 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal
- Position: Front
- Replaces: 23500286, 3860095, 03860095
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON | 8 Cyl 6.2L Diesel
View related parts
GMC Jimmy Seal Unit, Crankshaft Rear (Free Of Asbestos)
Part Number: 10121044
$36.04 MSRP: $56.68
You Save: $20.64 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1989 GMC Jimmy | 1/2 TON | 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
GMC Jimmy Seal,Crankshaft Rear Oil
Part Number: 10101164
$38.18 MSRP: $77.67
You Save: $39.49 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 GMC Jimmy | 1/2 TON
View related parts
GMC Jimmy Seal, Crankshaft Rear Main Bearing Cap
Part Number: 10191767
$13.05
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Cap, Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | 2 DOOR, 4 DOOR
View related parts
GMC Jimmy Seal,Crankshaft Rear Oil
Part Number: 12554314
$35.13 MSRP: $60.08
You Save: $24.95 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1998 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Seal Kit,Crankshaft Rear Oil
Part Number: 89018163
$26.79 MSRP: $44.34
You Save: $17.55 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL KIT, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Replaces: 12555769
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Seal Assembly, Cross Shaft Front Oil
Part Number: 10111769
$2.77 MSRP: $4.35
You Save: $1.58 (37%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Engine Front Cover & Crankshaft Seal
- Position: Front
- Replaced by: 10243247
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1991 GMC Jimmy | 1/2 TON | 8 Cyl 5.7L
View related parts
GMC Jimmy Seal Unit, Crankshaft Rear Oil (Free Of Asbestos)
Part Number: 23500139
Product Specifications
- Other Name: SEAL, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON | 8 Cyl 6.2L Diesel
View related parts
GMC Jimmy Seal,Rear Bearing Cap(O Ring)
Part Number: 10117767
Product Specifications
- Other Name: SEAL KIT, Engine Rear Main Bearing; Rear Main Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON

GMC Jimmy Crankshaft Seal

The Crankshaft Seal in GMC Jimmy automobiles is a critical part situated at the front aspect of the vehicle's engine. This metal and rubber seal is round and is usually used to eliminate the presence of oil leaks from the crankcase of a vehicle's engine. Crankshaft Seal ensures that components of the engine are well lubricated to reduce friction hence minimizing on the wear of its components. ld indicator like higher number of kilometer run on car or leakage of oil etc are potential cause of Crankshaft Seal then it could be change on regular basis for smoother running of car engine.

Each OEM GMC Jimmy Crankshaft Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Jimmy Crankshaft Seal Parts Questions & Experts Answers

Seal,Crankshaft Front Oil
10128316
Q: How to replace the front crankshaft seal on 2.2L four cylinder engine on GMC Jimmy?
A: Remove the cable from the negative battery terminal. Remove the drive belt. Raise the vehicle and securely place it on jackstands. Remove the hub retaining bolt. Place a bar through one of the pulley holes and wedge it against the bottom of the front cover to keep the pulley from turning while loosening the pulley bolts. Remove the pulley hub. Use a puller if necessary. Note how the seal is installed-the new one must face the same direction! Carefully pry the Crankshaft Seal out of the cover with a seal puller or a large screwdriver. Be very careful not to distort the cover or scratch the crankshaft! Apply a thin layer of engine oil or multi-purpose grease to the Crankshaft Seal lip and to the outer edge of the new seal. Install the seal in the cover with the lip (open end) facing IN. Drive the seal into place with a large socket and a hammer. Make sure the seal enters the bore squarely and is driven in until the front face is flush with the cover. The seal can also be replaced if the timing chain cover has been removed for other work. Support the cover on a block of wood and drive the seal out from the backside. Install a new seal into the bore. Reinstall the timing chain cover with a bead of RTV sealant applied to the mating surface of the oil pan. Apply a small amount of RTV sealant on the crankshaft Woodruff key. Align the slot in the hub with the crankshaft Woodriff key, then press the hub onto the crankshaft until it bottoms against the crankshaft timing gear. The hub retaining bolt can be used to press the hub into position. Install the crankshaft pulley on the hub. Use a non-hardening thread-locking compound on the bolt threads. Tighten the hub-to-crankshaft bolt. Install the drive belt.