How to replace the wheel cylinder on GMC Savana?

To replace the wheel cylinder on a vehicle, start by raising the rear of the vehicle and supporting it securely on jackstands. Block the front wheels to prevent the vehicle from rolling. Next, remove the brake shoe assembly and clean any dirt or foreign material from around the wheel cylinder. Disconnect the brake line, being careful not to pull it away from the wheel cylinder. Then, remove the wheel cylinder mounting bolts and detach the wheel cylinder from the brake backing plate. Immediately plug the brake line to prevent fluid loss and contamination. To install the new wheel cylinder, place it in position and install the bolts finger tight. Connect the brake line to the cylinder, ensuring it is not cross-threaded, and tighten the wheel cylinder mounting bolts to the correct torque specifications. Finally, tighten the brake line fitting securely, install the brake shoe assembly, bleed the brakes, and carefully check the operation of the brakes before driving the vehicle.

Genuine GMC Savana Wheel Cylinder

Brake Wheel Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Wheel Cylinders found

View related parts
GMC Savana Rear Brake Cylinder Assembly
Part Number: 19213345
$51.47 MSRP: $100.35
You Save: $48.88 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Wheel Brake Cylinder/Caliper; Wheel Cylinder
- Position: Rear
- Replaces: 18060026
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 GMC Savana | 3/4 TON CARGO EXPRESS, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER EXPRESS, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 5.7L
View related parts
GMC Savana Rear Brake Cylinder Assembly
Part Number: 19213344
$69.64 MSRP: $131.40
You Save: $61.76 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Wheel Brake Cylinder/Caliper; Wheel Cylinder
- Position: Rear
- Replaces: 18060024, 18004609
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 GMC Savana | 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RECREATIONAL VEHICLE EXPRESS, 1 TON COMMERCIAL/RECREATIONAL VEHICLE SAVANA, 1 TON PASSENGER, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 5.7L, 8 Cyl 6.5L Diesel, 8 Cyl 7.4L, 8 Cyl 8.1L
View related parts
GMC Savana Rear Brake Cylinder Assembly
Part Number: 19213355
Product Specifications
- Other Name: CYLINDER, Wheel Brake Cylinder/Caliper; Wheel Cylinder
- Position: Rear
- Replaces: 18060090
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2000 GMC Savana | 1 TON CARGO EXPRESS, 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RECREATIONAL VEHICLE EXPRESS, 1 TON COMMERCIAL/RECREATIONAL VEHICLE SAVANA, 1 TON PASSENGER, 3/4 TON CARGO EXPRESS, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER EXPRESS, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 5.7L, 8 Cyl 6.5L Diesel, 8 Cyl 7.4L

GMC Savana Wheel Cylinder

The hydraulic pressure applied by the GMC Savana Wheel Cylinder is turned into shoe force, which clamps brake shoes firmly against the drum, providing the stopping power every van needs. The pistons in a Wheel Cylinder can be pushed away from each other by applying liquid pressure to the cylinder. When the driver presses the pedal, brake fluid enters the center port, which makes the pistons slide out and press the shoes against the drum. Upon release, the return springs pull everything back while the Wheel Cylinder spring holds the seals in their seat. Older GMC vans made use of heavier cast units, whereas modern Savana applications are constructed from corrosion-resistant aluminum. However, both designs share a similar simple plunger design and, in some rear drum applications, a split dual single piston Wheel Cylinder design. Moisture will cause pitting in the bore, and leaking at the seal can drop the pedal height or seize the pistons, so whenever the shoes are serviced, the drivers must check each Wheel Cylinder. If honing brings back a smooth surface, restore with new seals or simply replace the cylinder. If the clearance gets to be excessive, just replace the cylinder. The healthy condition of the GMC Savana drums relies on identifying leaks sooner rather than later and acting before the braking power fades.

Each OEM GMC Savana Wheel Cylinder we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Savana Wheel Cylinder Parts Questions & Experts Answers

Rear Brake Cylinder Assembly
19213345
Q: How to replace the wheel cylinder on GMC Savana?
A:
To replace the wheel cylinder on a vehicle, start by raising the rear of the vehicle and supporting it securely on jackstands. Block the front wheels to prevent the vehicle from rolling. Next, remove the Brake Shoe assembly and clean any dirt or foreign material from around the wheel cylinder. Disconnect the Brake Line, being careful not to pull it away from the wheel cylinder. Then, remove the wheel cylinder mounting bolts and detach the wheel cylinder from the brake backing plate. Immediately plug the brake line to prevent fluid loss and contamination. To install the new wheel cylinder, place it in position and install the bolts finger tight. Connect the brake line to the cylinder, ensuring it is not cross-threaded, and tighten the wheel cylinder mounting bolts to the correct torque specifications. Finally, tighten the brake line fitting securely, install the brake shoe assembly, bleed the brakes, and carefully check the operation of the brakes before driving the vehicle.