How should I inspect and replace flexible brake hoses and brake line on Saturn Outlook?

About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the hoses exhibit any of the mentioned defects, they should be replaced with new ones. To remove a brake hose, clean all dirt away from the ends of the hose and unscrew the tube nut with a flare-nut wrench. Remove the bolts or clips securing the hose to the body and disconnect the hose from the caliper, discarding the sealing washers. Attach the new brake hose to the caliper using new sealing washers and tighten the banjo fitting bolt to the proper torque specifications. Make sure the hose isn't twisted during installation and check for any contact with suspension or steering components. Bleed the brake system after installation. When replacing metal brake lines, use the correct parts and avoid using copper tubing. Prefabricated brake lines with flared tube ends and fittings installed are available and can be bent to the proper shapes using a tubing bender. Ensure the new line is well supported in the brackets and has enough clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes carefully before normal operation.

Genuine Saturn Outlook Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Lines found

View related parts
Saturn Outlook Pipe,Brake
Part Number: 88983905
$68.97 MSRP: $134.44
You Save: $65.47 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PIPE, Hydraulic Brake; Brake Line
- Replaces: 25837622, 25837624, 84330459, 22726507, 84380488, 84330461
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Front Brake Hose Assembly
Part Number: 19366774
$32.68 MSRP: $61.64
You Save: $28.96 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,FRT BRK; Brake Hose, Flex Hose
- Position: Front
- Replaces: 15115039
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Front Brake Hose Assembly
Part Number: 19366775
$35.20 MSRP: $66.42
You Save: $31.22 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,FRT BRK; Brake Hose, Flex Hose
- Position: Front
- Replaced by: 19540597
- Replaces: 15115040
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Rear Brake Hose Assembly
Part Number: 19368466
$28.54 MSRP: $53.85
You Save: $25.31 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,RR BRK; Brake Hose, Flex Hose
- Position: Rear
- Replaces: 15921564, 23494652, 25800749
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Rear Brake Hose Assembly
Part Number: 19368465
$29.11 MSRP: $54.93
You Save: $25.82 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,RR BRK; Brake Hose, Flex Hose
- Replaced by: 19540594
- Replaces: 15921567, 25800751, 23494651
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Front Brake Pressure Mod Valve Pipe Assembly
Part Number: 15921562
$13.84 MSRP: $24.28
You Save: $10.44 (43%)
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L
View related parts
Saturn Outlook Brake Pressure Mod Valve Pipe Assembly
Part Number: 15115033
$5.00 MSRP: $8.78
You Save: $3.78 (44%)
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2010 Saturn Outlook | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD | 6 Cyl 3.6L

Saturn Outlook Brake Line

Saturn Outlook Brake Line is the highway of fluid that transmits hydraulic pressure from the master cylinder to each caliper to provide the SUV with its stopping power. Built as either rigid steel tubing or flexible rubber hose, the Brake Line network combines strength with flexibility. This means pressure moves instantly when the driver presses on the pedal. Within the Saturn chassis, the metal sections run along frame rails where they face winter road salt, debris, and off-road impacts that can dent, corrode, or even puncture the line. Any hole lets fluid escape and pressure vanish. Rubber hose segments connect moving suspension components, but aging can result in hardening of the rubber, which allows the appearance of cracks, bulges, or swelling of the rubber hose. Improper routing can cause abrasion against components until weakness develops. A damaged Brake Line may leak fluid, erasing pedal feel, and on any Outlook model, fittings may twist the tube apart during service. If the steel fittings are seized by corrosion, forcing them out will twist the tube apart. Careless clamping will crush a hose and cause a hidden restriction that drags a wheel or creates a spongy pedal. Replacing a Brake Line that shows severe corrosion or abrasion is the only safe cure. Visual checks for rust flakes, dents, cracks, or bulges help keep the Brake Line system healthy across every Saturn Outlook adventure.

Each OEM Saturn Outlook Brake Line we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Saturn Outlook Brake Line Parts Questions & Experts Answers

Pipe,Brake
88983905
Q: How should I inspect and replace flexible brake hoses and brake line on Saturn Outlook?
A:
About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the hoses exhibit any of the mentioned defects, they should be replaced with new ones. To remove a brake hose, clean all dirt away from the ends of the hose and unscrew the tube nut with a flare-nut wrench. Remove the bolts or clips securing the hose to the body and disconnect the hose from the caliper, discarding the sealing washers. Attach the new brake hose to the caliper using new sealing washers and tighten the banjo fitting bolt to the proper torque specifications. Make sure the hose isn't twisted during installation and check for any contact with suspension or steering components. Bleed the brake system after installation. When replacing metal brake lines, use the correct parts and avoid using copper tubing. Prefabricated brake lines with flared tube ends and fittings installed are available and can be bent to the proper shapes using a tubing bender. Ensure the new line is well supported in the brackets and has enough clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes carefully before normal operation.