Make sure this part fits

GM 15806655 Power Brake Booster ASSEMBLY

2006-2008 GM

Customer Questions & Expert Answers (3)
GM 15806655 Power Brake Booster ASSEMBLY
  • Part Description
    Booster Assembly, Power Brake ; Booster, Hydraulic Power Brake Booster
  • Replaces
    19121403
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number15806655
    Part DescriptionBooster Assembly, Power Brake ; Booster, Hydraulic Power Brake Booster
    Other NamesBrake Booster, Power Booster
    Item Dimensions16.6 x 13.9 x 14.1 inches
    Item Weight12.80 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces19121403
    ManufacturerGeneral Motors
    SKU15806655
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2006-2008 Chevrolet Impala6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9LLS, LS POLICE CAR, LT, LT 3.5, LTZ, SS
    2006-2007 Chevrolet Monte Carlo6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9LLS, LT, SS
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 15806655 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install a brake booster on Chevrolet Monte Carlo? Posted by Customer
    A:
    Remove your foot from the brake pedal once the engine is turned off, then test if there are any changes in the distance it travels. Push down on the pedal and turn on the engine to observe if it takes a slight drop. Air tightness check: Start the engine and allow it run for one to two minutes before turning it off. With your foot gently on the brake pedal, press slowly down several times, ensuring that you note whether there is an immediate drop during initial depression but after subsequent depressions rises gradually. While holding for 30 seconds, press the brake pedal while the engine is running and shut off the engine. Removal and installation: Turn ignition key to OFF position and depress brake pedal several times to deplete vacuum in power assist booster. Apply parking brake and loosen lug nuts on left front wheel.Raise left front of vehicle and support securely with jack stands.Remove left front wheel.Remove upper engine cover. Remove air filter housing.Remove all ABS hydraulic control unit mounting bracket fasteners and carefully slide unit aside.Unbolt master cylinder from power booster.On V8 models as well as 2004-2008 V6 models remove exhaust crossover pipe from between manifolds.On 2009 up V6 engines drain cooling system; remove heater pipes which go under throttle body.Detach check valve then electrical connector if equipped from power brake booster.Pull out brake pedal position sensor.Remove retaining clip holding booster pushrod to brake pedal arm.In engine compartment, remove mounting bolts for coolant pipe brackets on V8 engine models.Inside vehicle, remove pushrod from brake pedal arm.Turn booster counterclockwise until free of its mount.Carefully slide booster assembly out from under hood.Installation is reverse of removal making sure booster retaining tang fully engages into its bracket at firewall base while tang at base of booster firmly engages bracket on firewall.Put in new retaining clip securing push rod coming out of brake booster to arm of brake pedal.Tighten master cylinder mounting fasteners. Carry out a full functional test of the brakes before returning vehicle to normal service.
    Posted by GMPartsGiant Specialist
    Q:
    What additional steps are required for removing the brake booster on the 2008 Chevrolet Impala? Posted by Customer
    A:
    - Remove the ABS hydraulic control unit mounting bracket fasteners and carefully place the unit aside. Remove the master cylinder from the power booster. Remove the exhaust crossover pipe from between the manifolds.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Brake Booster
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 15806655, the Right Choice

To ensure reliability, purchase GM part # 15806655 Power Brake Booster ASSEMBLY. It is sometimes referred to as GM Brake Booster. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Chevrolet Impala, Monte Carlo models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 15806655 Power Brake Booster ASSEMBLY. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Chevrolet parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly