Saturn 1999437 Bulb, Headlamp(High Beam)

The process to change right-side truck model bulbs starts with removing the air filter housing. The replacement process for a left-side bulb on a truck model with an auxiliary battery requires first removing the battery from its position. Use a twisting motion to separate the headlight bulb electrical connector while rotating the bulb holder clockwise and finally removing it from the housing. The steps for installation follow the exact opposite process for removal.

Remove the four headlight retaining ring screws, then take off the retaining ring, pull out the headlight, and disconnect the electrical connector. After that, take out the headlight unit from the vehicle. To install, reverse the removal process.

To replace the right-side headlight bulb, first put off the battery. Subsequently, turn the bulb and holder in the anti-clockwise direction to unlock from the headlight housing. Then, in order to release the bulb, remove it from the housing and disconnect the electrical connector from the bulb. Screw the electrical connector to the new headlight bulb then screw the bulb correctly into the headlight housing. In the case of the headlight housing you should first take off the grille and then the headlight housing screws. Pop out the headlight housing from the body and open the connector levers to remove the electrical connectors of the bulb holders. Removal is the mirror image of installation.

If you're replacing a right-side bulb on a truck model, remove the air filter housing. If you're working on an SUV model, remove the headlight housing. Disconnect the headlight bulb electrical connector, rotate the bulb holder counterclockwise, and remove it from the housing. Installation is the reverse of removal.

To work on headlights for these SUV models-Suburban, Tahoe, Yukon, Yukon XL, and Yukon Denali-start by taking off the housing. Begin by unplugging the bulb connector. Turn the bulb holder in the opposite direction and pull it out from the housing. First, do the steps of removal in reverse order to install.

To disconnect the negative cable from the battery, start by removing the radiator grille for sealed beam-type headlights. Then, carefully remove the retainer screws without disturbing the adjusting screws. Pull the headlight out enough to unplug the connector and remove the headlight. To install the headlight, plug the connector in, position the headlight, and secure it with the retainer and screws. For composite headlights, open the hood and remove the two headlight retainers to drop the assembly forward and down. Reach behind the assembly to turn the bulb holder counterclockwise and unplug it. To install, plug the new bulb assembly into the electrical connector, insert it into the receptacle, and rotate clockwise to lock it into place.

Start by taking out the headlight housing then you will have to disconnect the electrical connection to the bulb holder. Further, with a quick anticlockwise turn you can pull off the bulb holder from the housing section. One has to be careful not to touch the bulb glass with bare hands when fixing the new bulb assembly; in order to replace the assembly, one has to slide it into the headlight housing and then turn it clockwise to lock it into place. Last but not the least, join the electrical connector.

Unplug it from the bulb holder and reconnect it to the new bulb/holder.

Remove the cover(s) for access to the bulb(s) and disconnect the electrical connector(s) from the headlight housing.

To install, plug the new bulb assembly into the electrical connector, insert it into the receptacle, and rotate clockwise to lock it into place.

Start by opening the hood to access the bulb from behind the headlight housings. In some cases, you may need to remove the radiator grille to gain access.

Take off the headlamp bezel by unhooking the screws on either side and releasing the three tabs, ensuring to protect the car's finish during this process.

For composite headlights, open the hood and remove the two headlight retainers to drop the assembly forward and down. Reach behind the assembly to turn the bulb holder counterclockwise and unplug it.

Start by removing the inner fender splash shield.

To install a new bulb, handle it only by the bulb holder portion and reconnect the electrical connector.

To install, plug the new bulb assembly into the electrical connector, insert it into the receptacle, and rotate clockwise to lock it into place.

The auxiliary battery needs to be removed.

Twist it clockwise to secure it in place.

The auxiliary battery needs to be removed.

Detach the cable from the negative terminal of the battery, ensuring that the lockout feature of the Theft lock audio system is turned off if equipped.