Saturn 22692679 Bulb, Back Up Lamp (Trade #921Ll)

Exterior light bulbs are made up of the following; front turn signal/parking light bulbs, fog light bulbs, center high-mounted stop light, rear brake/tail, turn signal, brake and back-up light bulbs, license plate light bulbs. Interior light bulbs include reading light bulbs, cargo and dome light bulb, and instrument cluster light bulbs. To replace these bulbs follow the steps below. For front turn signal/parking light bulbs remove headlight housing then turn the bulb holder counterclockwise then pull the bulb out straight from its holder then reverse installation by reversing the steps above. In case of any difficulty while replacing a fog lamp bulb, jack stand should be used to raise the front end of the vehicle so as to easily access backside of fender liner. Fender inner liner or splash shield also needs to be removed in order to get access to fog lamp electrical connector. After that counterclockwise rotate it until you can remove it then attach new one and use reverse procedure for remounting all other parts. While replacing center high mounted stop lamp you will need to take upper interior trim panel away from liftgate hence giving space for spoiler mounting screws removal before disconnecting electrical connector prior installing new unit using this same process in reverse order. For rear brake/tail lights, turn signals, brake lights, and backup lamps-open liftgate window first then get upward vision at both screws that hold taillight housing on place before pulling entire assembly outwards followed by turning bulb holder against clockwise direction so as to take off lighting source from socket itself before returning everything back as it was originally organized. Open liftgate and take out two screws holding license plate lens cover until you manage pulling off a little glass with your fingers followed by reversing these steps for installation purposes only if needed (as per user manual). To replace interior lights like reading lamp one should remove its lens which is normally located at front or centre area, then pull out a light bulb thus reversing above described steps. Other types of interior lighting devices such as cargo or dome lights can be repaired by unplugging both leads (they are often located on either side of fixture) after unscrewing lens from each one to get access its socket before returning everything accordingly. Instrument cluster lights need the user to remove the entire instrument cluster in order to reach the bulb socket where they can make small movements using a tiny screwdriver so that it comes off from there and reverse procedure will cover this gap between old installation removed during both disassembly stages.

In order to have some extra illumination at night, let alone replace exterior lights, the first step is to take out the headlight housing. In the case of front side marker light bulbs, the bulb holder should be twisted anticlockwise to be unlocked, the old bulb can then be removed and a new bulb inserted until it is locked in place. The same applies to front park and turn signal bulbs. For the fog lights, they have a bulb holder that should be unscrewed in anticlockwise direction, after which one removes the electrical connector and the assembly is replaced as a complete unit. For center high mount brake light on Impala models, first open trunk then remove the carpet trim, to detach the housing one has to remove the mounting nuts and also disconnect electrical connector. On Monte Carlo models, unscrew the mounting bracket and have it plateau, and disconnect the electric connector. License plate light bulbs can be replaced from the rear of the car or from the inside if one has to remove the license plate; to replace the bulbs twist a small dial around the base of the holder counter clockwise and place a new bulb in the holder after removing the expired one. For taillights bulbs, open the trunk pull the carpeting retainer, disconnect the housing by unscrewing the plastic wing nuts and then disconnect the electrical connector. Twist the bulb holder anti-clockwise, eject the previous bulb, and replace with a new one. for replacement of back-up light bulbs on Monte Carlo models; the screws holding the housing should be unscrewed to release the housing then pulled out, to remove the bulb holder, rotate it anti-clockwise then install a new bulb. For interior lights remove the dome light lens, remove the old bulb, and replace it with a new one by placing the bulb and pushing it upwards to lock it in place. For reading light bulbs, especially, one must put off the lens then remove the old bulb before placing a new bulb properly until it is tight with lens back in the right place. The instrument panel courtesy light bulb is behind the glove box; you only need to slide it to replace it.

In order to have some extra illumination at night, let alone replace exterior lights, the first step is to take out the headlight housing. In the case of front side marker light bulbs, the bulb holder should be twisted anticlockwise to be unlocked, the old bulb can then be removed and a new bulb inserted until it is locked in place. The same applies to front park and turn signal bulbs. For the fog lights, they have a bulb holder that should be unscrewed in anticlockwise direction, after which one removes the electrical connector and the assembly is replaced as a complete unit. For center high mount brake light on Impala models, first open trunk then remove the carpet trim, to detach the housing one has to remove the mounting nuts and also disconnect electrical connector. On Monte Carlo models, unscrew the mounting bracket and have it plateau, and disconnect the electric connector. License plate light bulbs can be replaced from the rear of the car or from the inside if one has to remove the license plate; to replace the bulbs twist a small dial around the base of the holder counter clockwise and place a new bulb in the holder after removing the expired one. For taillights bulbs, open the trunk pull the carpeting retainer, disconnect the housing by unscrewing the plastic wing nuts and then disconnect the electrical connector. Twist the bulb holder anti-clockwise, eject the previous bulb, and replace with a new one. for replacement of back-up light bulbs on Monte Carlo models; the screws holding the housing should be unscrewed to release the housing then pulled out, to remove the bulb holder, rotate it anti-clockwise then install a new bulb. For interior lights remove the dome light lens, remove the old bulb, and replace it with a new one by placing the bulb and pushing it upwards to lock it in place. For reading light bulbs, especially, one must put off the lens then remove the old bulb before placing a new bulb properly until it is tight with lens back in the right place. The instrument panel courtesy light bulb is behind the glove box; you only need to slide it to replace it.

Exterior light bulbs are made up of the following; front turn signal/parking light bulbs, fog light bulbs, center high-mounted stop light, rear brake/tail, turn signal, brake and back-up light bulbs, license plate light bulbs. Interior light bulbs include reading light bulbs, cargo and dome light bulb, and instrument cluster light bulbs. To replace these bulbs follow the steps below. For front turn signal/parking light bulbs remove headlight housing then turn the bulb holder counterclockwise then pull the bulb out straight from its holder then reverse installation by reversing the steps above. In case of any difficulty while replacing a fog lamp bulb, jack stand should be used to raise the front end of the vehicle so as to easily access backside of fender liner. Fender inner liner or splash shield also needs to be removed in order to get access to fog lamp electrical connector. After that counterclockwise rotate it until you can remove it then attach new one and use reverse procedure for remounting all other parts. While replacing center high mounted stop lamp you will need to take upper interior trim panel away from liftgate hence giving space for spoiler mounting screws removal before disconnecting electrical connector prior installing new unit using this same process in reverse order. For rear brake/tail lights, turn signals, brake lights, and backup lamps-open liftgate window first then get upward vision at both screws that hold taillight housing on place before pulling entire assembly outwards followed by turning bulb holder against clockwise direction so as to take off lighting source from socket itself before returning everything back as it was originally organized. Open liftgate and take out two screws holding license plate lens cover until you manage pulling off a little glass with your fingers followed by reversing these steps for installation purposes only if needed (as per user manual). To replace interior lights like reading lamp one should remove its lens which is normally located at front or centre area, then pull out a light bulb thus reversing above described steps. Other types of interior lighting devices such as cargo or dome lights can be repaired by unplugging both leads (they are often located on either side of fixture) after unscrewing lens from each one to get access its socket before returning everything accordingly. Instrument cluster lights need the user to remove the entire instrument cluster in order to reach the bulb socket where they can make small movements using a tiny screwdriver so that it comes off from there and reverse procedure will cover this gap between old installation removed during both disassembly stages.

To replace these bulbs, carefully pry the lens out, pull the bulb from the socket, and reinstall in reverse order.

Rotate the bulb holder counterclockwise and pull the bulb out. On some models, the side marker light is a separate unit mounted in the front fender, and access to the bulb is from underneath the fender (the inner fender splash shield will have to be partially removed).

Pry off the dome light or map reading light lens, remove the bulb by disengaging the retaining wire, and reinstall in reverse order.