How to access and replace the knock sensors on Cadillac Escalade?

The knock sensors are mounted in two, 1 is left side of block and knock sensor 2 is on the right side above the starter motor. It is however difficult to access the knock sensors since they are located beneath the exhaust manifolds. First of all, lift the front of the car and secure it on jackstands to prevent slipping during the work. For all other models except 6.0L and 4WD, it may be required to drop the front driveshaft to get at knock sensor 1. In 6.0L models, to replace knock sensor 2, one has to remove the starter. For models other than 6.0 L, location and fastenings-knock sensor heat shield bolt and, depending on the car model, the heat shield should be removed. Remove the electrical connector with the left-side knock sensor that is located on the engine block to the front of the oil filler housing. Secondly, you should pull out the knock sensor retaining bolt then take out the knock sensor. Installation is done in reverse order of removal, where it is made certain that the knock sensor retaining bolt is tightened to the recommended torque.

Genuine Cadillac Escalade Knock Sensor

Engine Knock Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Knock Sensors found

View related parts
Cadillac Escalade Sensor,Knock
Part Number: 12589867
$65.53 MSRP: $133.68
You Save: $68.15 (51%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Replaces: 10456603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Cadillac Escalade | 1/2 TON, 3/4 TON, EXT 1/2 TON, EXT 3/4 TON, YUKON/DENALI/ESCALADE | 8 Cyl 5.3L, 8 Cyl 6.0L
View related parts
Cadillac Escalade Sensor,Knock
Part Number: 10456288
$47.77 MSRP: $97.45
You Save: $49.68 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); ESC Sensor, Knock Sensor
- Replaces: 10456018
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | 1 TON CREW CAB, 1/2 TON, 3/4 TON, 4 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON, CREW CAB 1 TON, EXTENDED CAB 1 TON, EXTENDED CAB 6'6" BOX 1/2 TON, EXTENDED CAB 6'6" BOX 3/4 TON, EXTENDED CAB 8' BOX 3/4 TON, K2500 CREW CAB, K3500 CAB CHASSIS 135.5, K3500 CAB CHASSIS 159.9, REGULAR CAB 1 TON, REGULAR CAB 3/4 TON, YUKON/DENALI/ESCALADE | 8 Cyl 5.7L
View related parts
Cadillac Escalade Sensor Assembly, Knock
Part Number: 12623730
$13.41 MSRP: $25.30
You Save: $11.89 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Replaces: 12570125
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.2L, 8 Cyl 6.2L Flex
View related parts
Cadillac Escalade Sensor Assembly, Knock
Part Number: 12623095
$23.32 MSRP: $44.02
You Save: $20.70 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2024 Cadillac Escalade | 1/2 TON, 1500 4 DOOR, 1500 4 DOOR SUV, 1500 4 DOOR UTILITY, 1500 CREW CAB, 1500 CREW CAB STANDARD BOX, 4 DOOR 1/2 TON, CLASSIC 1500 CREW CAB LONG BOX, CLASSIC 1500 EXTENDED CAB STANDARD BOX, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Cadillac Escalade Sensor Assembly, Knock
Part Number: 12591312
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Replaces: 10456500
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Cadillac Escalade | 3/4 TON, EXT 3/4 TON

Cadillac Escalade Knock Sensor

The Knock Sensor in Cadillac Escalade vehicles is very useful when it comes to rendering performance to the engines since it is responsible for recognizing Engine knock which is normally caused by an incorrect ignition time. This device communicates with the PCM to allow it to vary ignition timing and minimize detonation that is too strong. In most Cadillac Escalade models piezoelectric knock sensors are commonly used in the engines to monitor pressure peaks and knock continuously through detection of shock vibrations. Cadillac Escalade in recent pasts has integrated knock sensor that allows the vehicle to change ignition timing for particular cylinder and control boost pressure depending on the design of the engine. This makes it to deliver its expected power and to last longer on the engine, regardless of the fuel grade used. The Cadillac Escalade's knock sensor system is one of the greatest representations of modern engine management systems because of its efficiency and accuracy.

Each OEM Cadillac Escalade Knock Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Escalade Knock Sensor Parts Questions & Experts Answers

Sensor Assembly, Knock
12623095
Q: How to access and replace the knock sensors on Cadillac Escalade?
A:
The knock sensors are mounted in two, 1 is left side of block and knock sensor 2 is on the right side above the starter motor. It is however difficult to access the knock sensors since they are located beneath the exhaust manifolds. First of all, lift the front of the car and secure it on jackstands to prevent slipping during the work. For all other models except 6.0L and 4WD, it may be required to drop the front driveshaft to get at knock sensor 1. In 6.0L models, to replace knock sensor 2, one has to remove the starter. For models other than 6.0 L, location and fastenings-knock sensor heat shield bolt and, depending on the car model, the heat shield should be removed. Remove the electrical connector with the left-side knock sensor that is located on the engine block to the front of the oil filler housing. Secondly, you should pull out the knock sensor retaining bolt then take out the knock sensor. Installation is done in reverse order of removal, where it is made certain that the knock sensor retaining bolt is tightened to the recommended torque.