GMC 12690512 Valve Assembly, Evap Emis Cnstr Purge Sol

Disconnect the cable from the negative battery terminal, then open the fuel filler cap to relieve the fuel pressure in the tank and remove the engine covers. For 3.2L V6 engines, disconnect the EVAP canister purge valve vacuum line from the top of the intake manifold, the coil pack electrical connector, the electrical connector from the canister purge valve, and the EVAP line quick-connect fittings. Remove the purge valve and mounting bracket as a single assembly, then detach the purge valve from the mounting bracket, with installation being the reverse of removal. For all 2009 and earlier models except 3.2L V6 engines, disconnect the purge line quick-connect fittings from the purge valve, the electrical connector from the canister purge valve, loosen the mounting bracket, and remove the purge valve, again reversing the process for installation. For 2010 and later models, disconnect the electrical connector from the canister purge valve, the EVAP line quick-connect fittings, and remove the canister purge valve mounting bolt to take the valve from the manifold, with installation being the reverse of removal. The EVAP canister is located under the vehicle, above the rear suspension and subframe; raise the vehicle and support it securely on jackstands, then remove the rear subframe and suspension, disconnect the electrical connector and the vapor hose quick-connect fitting from the EVAP canister vent solenoid, disconnect the two EVAP line quick-connect fittings from the EVAP canister, remove the mounting fasteners securing the canister, and take out the canister, with installation being the reverse of removal. For the EVAP canister vent solenoid, remove the rear subframe and suspension, disconnect the canister vent solenoid electrical connector, rotate the valve counterclockwise, and remove it from the canister, with installation being the reverse of removal.

To remove the fuel tank pressure sensor, take out the fuel tank, disconnect the connector, and remove the sensor from the fuel pump module. To remove the EVAP canister, raise the vehicle, remove the fuel tank, disconnect the connector and hoses from the canister on top of the tank, and remove the retainer and the canister. Installation is the reverse of removal.

First, remove the cable from the negative terminal of the battery and twist open the fuel filler cap in order to release the pressure within the tank of the automobile. While in the V6 models, the canister purge solenoid valve is at the right side of the intake manifold as for the V8 models it is at the front of the engine. This valve can be removed by removing the engine cover, then the electrical connector from the canister purge valve, the EVAP line quick-connect fitting, followed by unscrewing the mounting bolt to remove the valve The procedures for installation are done in reverse. The EVAP canister is stored under the car, to the rear of the car body, above the rear suspension subframe. Lift the car and provide it with jackstands, and then have the fuel tank removed. When draining the fuel tank, remove the electrical connection from the EVAP canister vent solenoid, the vapor hose quick-connect fitting together with the two EVAP line quick-connect fittings of the EVAP canister. Remove the mounting bolts and remove the canister from the floor pan and the procedure of installation is vice-versa. To remove a canister vent solenoid, one has to remove the canister as indicated above, then, disconnect the canister vent solenoid electrical connector, turn the vale anti-clockwise and pull off from the canister The process of putting the valve back is the same as above.

EVAP Purge Solenoid Valve Removal involves removing the engine cover, disconnecting the electrical connector from the valve, disconnecting the hose, unscrewing the bolt and removing the purge valve from the upper intake manifold. Installation is simply the reverse of removal. For EVAP Canister Removal, raise the vehicle and support it securely on jackstands. Then, disconnect the hoses from the canister, disconnect the electrical connector from the canister vent solenoid valve, remove the fasteners securing the canister, and remove the canister. Installation is again the reverse of removal.

EVAP Purge Solenoid Valve Removal involves removing the engine cover, disconnecting the electrical connector from the valve, disconnecting the hose, unscrewing the bolt and removing the purge valve from the upper intake manifold. Installation is simply the reverse of removal. For EVAP Canister Removal, raise the vehicle and support it securely on jackstands. Then, disconnect the hoses from the canister, disconnect the electrical connector from the canister vent solenoid valve, remove the fasteners securing the canister, and remove the canister. Installation is again the reverse of removal.

To remove the fuel tank pressure sensor, take out the fuel tank, disconnect the connector, and remove the sensor from the fuel pump module. To remove the EVAP canister, raise the vehicle, remove the fuel tank, disconnect the connector and hoses from the canister on top of the tank, and remove the retainer and the canister. Installation is the reverse of removal.

Disconnect the hose from the EVAP purge control solenoid valve.

84115531 PIPE

No, this is just the EVAP canister itself

Yes, it comes with 1 screw

The canister is located on the passenger side of the engine compartment