Make sure this part fits

Oldsmobile 25527077 Valve Kit, Idle Air Control (Throttle Body)

1984-1994 Oldsmobile

Customer Questions & Expert Answers (8)
GM 25527077 Valve Kit, Idle Air Control (Throttle Body)
  • Part Description
    VALVE KIT, Throttle Body/Carburetor
  • Replaces
    17111460, 17111288
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Oldsmobile
    Manufacturer Part Number25527077
    Part DescriptionVALVE KIT, Throttle Body/Carburetor
    Item Dimensions3.2 x 2.1 x 2.1 inches
    Item Weight0.50 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces17111460, 17111288
    ManufacturerGeneral Motors
    SKU25527077
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1985-1986 Oldsmobile 986 Cyl 3.8LREGENCY 2 DOOR, REGENCY 4 DOOR, REGENCY BROUGH 2 DOOR, REGENCY BROUGH 4 DOOR
    1991-1994 Oldsmobile Bravada6 Cyl 4.3LBRAVADA
    1991-1992 Oldsmobile Custom Cruiser8 Cyl 5.0L, 8 Cyl 5.7LSTATION WAGON
    1984-1988 Oldsmobile Cutlass6 Cyl 3.8L2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON
    1986 Oldsmobile Delta 882 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR
    1990-1994 Oldsmobile Silhouette6 Cyl 3.1LMPV
    1986 Oldsmobile Toronado6 Cyl 3.8LBROUGHAM
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 25527077 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install idle control valve assemblies on Buick Regal? Posted by Customer
    A:
    For the purpose of removal and replacement of idle control valve assemblies there is a need to unplug the electrical connection to the valve. To remove the valve, you require an appropriate wrench this being 1 1/4 inches (32mm) in diameter. To install, reverse all these processes while it is recommended that it is done within one and an 1/8 inch (28mm) from the motor housing to the tip of the cone to prevent damage. A new gasket must be had and the ignition switched on and off to allow the idle control valve to adjust. Thus determine if the replacement valve is either of Type 1 which has a collar at the electric terminal end of the valve or the Type 2 that does not have the collar. If the measured distance is more than this distance, for Type 1, apply downward pressure on the valve to reset it; for Type 2, push in the retaining spring while rotating the valve anticlockwise, then release the spring and align the flat end of it with the counterpart part of the valve.
    Posted by GMPartsGiant Specialist
    Q:
    What is the proper procedure for replacing fuel injectors, throttle position sensor, Idle Control Valve and throttle body assembly on Pontiac Firebird? Posted by Customer
    A:
    Open the fuel injector rail pressure release valve, then disconnect the cable from the negative terminal of the battery before turning off the anti-hood jacking system and on Delco Loe II audio system, do the same. Covers and plates, air cleaner housing assembly, EOx20EGC1100 adapter, and gaskets should be removed. The fuel pressure regulator is incorporated in the fuel meter cover and if the assembly is being worked on or the fuel meter cover is being changed, the entire holder has to be replaced. Disconnect the electrical connectors from the fuel injectors, remove the fuel meter cover screws and then remove the fuel meter cover. Take out the gaskets and clean out all previous gasket material used as they are not to be reused. Clean the metal casing and any lenses which are on the top or sides of the cover if it is located in a retail store, replace the gaskets and seals if required. When refitting the fuel meter cover use the Loctite 262 on the screws before reconnecting the electrical connectors to the injector and the negative terminal of the battery. Ensure to do the check with the engine off, but with the ignition on prior to reinstalling the air cleaner assembly. When replacing fuel injectors ensure that they are of the exact part number, disconnect the connectors and finally dismantle the fuel meter cover assembly using the special spanner but without having to remove the gasket. Remove the injectors, remove the O-rings and filters then check for contamination. Before you fit the new O-rings it is important to ensure that they are soaked in automatic transmission fluid. After putting the injectors properly in place, equally replace the fuel meter cover. By doing so you will ensure that there are no more leaks after having reconnected the battery. For the throttle position sensor, one should remove this component from the throttle body but should not use any liquid cleaners for the same and then fix the lever in the right manner when reinstalling this component. For the idle air control valve, as given in the procedure disconnect the connector then disconnect the valve, remove the old gasket and make sure that the new one fits correctly. This pintle should be adjusted as required prior to being reattached. To disassemble the fuel meter body assembly, first, disconnect the connectors, then uninstall the assembly and undo the fuel lines connection also note the position of the nut for reassembly. Ensure that gaskets have been replaced well and all joints are well tightened. For the throttle body assembly there should be disconnecting of all connectors, removal of linkages and the throttle body together with removal of the gasket will also be dumped. Wash the assembly without immersing any delicate parts, look for signs of wear and tear and replace the IAC valve and TPS. Tighten all the joints, check that there is no interference of the accelerator pedal, and connect the negative terminal of the battery. They are to check for oil leaks, warm up the engine and also to adjust the idle speed. When you find it necessary, then follow the laid down procedures of synchronization and alignment.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done during the installation of the valve for the 1986 Buick Century? Posted by Customer
    A:
    During installation, reverse the removal steps and ensure to measure the extended distance of the valve from the motor housing to the end of the cone, which should not exceed 1 1/8 inches (28mm) to avoid potential damage.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Idle Control Valve
    Q:
    What is the purpose of the Idle Air Control (IAC) system of the 1993 Cadillac Fleetwood? Posted by Customer
    A:
    The purpose of the IAC system is to control engine idle speeds and prevent stalls caused by changes in engine load.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Idle Control Valve
    Q:
    What are the initial steps to prepare for replacing the throttle body assembly for the 1990 Chevrolet Astro? Posted by Customer
    A:
    To prepare for replacing the throttle body assembly, you should first relieve the fuel pressure and detach the cable from the negative terminal of the battery.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Idle Control Valve
    Q:
    How is the idle speed regulated for the 1993 Chevrolet C1500? Posted by Customer
    A:
    The idle speed is regulated by the ECM/PCM, which controls the IAC valve.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Idle Control Valve
    Q:
    What should be done before installing a new IAC valve for the 1990 Chevrolet K1500? Posted by Customer
    A:
    Before installing a new IAC valve, measure the distance from the tip of the pintle to the mounting flange and adjust it if necessary. Install a new O-ring, lubricate it, and securely tighten the valve.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Idle Control Valve
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 25527077, the Right Choice

To ensure reliability, purchase GM part # 25527077 Valve Kit, Idle Air Control (Throttle Body). It is sometimes referred to as Oldsmobile Idle Control Valve. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Oldsmobile Bravada, Custom Cruiser, Cutlass models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 25527077 Valve Kit, Idle Air Control (Throttle Body). You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Oldsmobile parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly